User manual CLARION TB733W

[. . . ] Owner's manual & Installation manual IN-DASH WIDE 7" COLOR LCD TV Clarion Co. , Ltd. All Rights Reserved. Copyright © 2003: Clarion Co. , Ltd. 2003/3 (A·C) QZ7532K 280-7960-00 English Owner's manual Thank you for purchasing the Clarion TB731P/TB732P/TB733W. * Please read this Owner's manual & Installation manual in its entirety before proceeding with wire connection and installation. * After reading this manual, be sure to keep it in a handy place (e. g. , glove compartment). I Contents · Owner's manual 1. [. . . ] Press the [MEMO] button, the manual memory screen is displayed. While the channel display at the left of the screen turns red, the manual memory operation is available. TV1 WIDE TV1 NORMAL Manual tuning Press the [a] or [d] button to select the channel. The channel number appears at the top right of the screen. The picture at the left and right of the screen is stretched in the sideways direction. In wide mode, the picture is stretched in both the upward and downward direction when a PAL signal is received. Black bands appear to the left and right of the screen. Each time the [a] or [d] button is pressed, the channel number is incremented or decremented by 1. The channel number remains on the screen for about 5 seconds. I For wide (16:9) picture reception Use the cinema mode. G Normal mode Preset memory function G Cinema mode 62 62 Wide mode, full wide TV1 NORMAL TV1 CINEMA The number of preset channels which can be stored in the memory is: · 6 stations for TV1 · 6 stations for TV2 Total of 12 stations Any station can be stored in any preset channel. } 3. Press the [a] ro [d] button to select the channel to be preset. Press the [w] or [z] button to select the preset channel in which the station to be stored. Press the [MEMO] button for 1 second or longer to store the station into the preset memory. To cancel the manual memory mode, press the [MEMO] button again and press the [DISP] button. Note: · The memory contents are returned to the default settings when the battery is replaced or the power supply is otherwise suspended. Black bands appear all around the screen. The picture is shown expanded so that it fills the whole screen. 12 TB731P/TB732P/TB733W TB731P/TB732P/TB733W 13 TV Mode Operations Preset scanning 1. The stations stored in the preset channels are received in sequence at intervals of about 5 seconds per station. TV1 1 2 3 4 5 6 F. WIDE TV Mode Operations Adjusting the brightness and tone of color 1. Display the adjustment menu as described in the section, "Selecting the adjustment menu". Press the [Î] button to display the picture quality adjustment screen. Hue adjustment is not possible in PAL mode. "HUE" and "COLOR" operations are available only when the car is stopped and the parking brake is applied. BRIGHT English Owner's manual English Press the [BND] button when all adjustments have been made to return to the adjustment menu screen. Press the [ADJ] button to return to the normal screen mode. Selecting the FM modulator frequency (TB731P/TB732P only) 1. Display the adjustment menu as described in the section, "Selecting the adjustment menu". [ MONI [ ADJ ] ] Owner's manual 62 Setting the beep The sound heard when you make operations is called "beep". The unit can be set up so that it does not produce this beep sound. The factory default setting is "ON". BEEP P. SCAN [ MODULATER ] MODU FREQ 2. To release the preset scanning, press the [PS] button again. 1. Display the adjustment menu as described in the section. "Selecting the adjustment menu". ADJ 1 Preset selection 1. Press the [BND] button to select TV1 or TV2. Press the [w] or [z] button to select the preset channel. [. . . ] Be particularly careful where you route the wires. Keep them well away from the engine, and exhaust pipe, etc. When connecting the ground lead, fasten the ground lead (black) securely to a clean metal plate on the car. (Figure 10) If the set is insufficiently grounded, it may not operate or there may be noise. [. . . ]