User manual CLARION VDH9600 INSTALLATION MANUAL

[. . . ] · Use only supplied screws and hardware. Make sure all connections and components are fastened securely. · At the proposed installation site, make sure there is adequate space to accommodate the unit's dimensions (and mounting brackets) and provide adequate ventilation (see Installation on page 14). · Use extreme caution when drilling around electrical wiring, brake lines, and fuel lines. [. . . ] Press the EJECT function to remove the internal cassette to prevent damage. See page 9 8 Remote IR Sensor opening Allows the IR to function through the front of the player. t STILL/SLOW Button Press to view a single frame. Hold down the button to slow search for a desired video segment frame by frame. 9 STOP Button Press to stop any play, fast forward, or rewind mode. 6 OWNER'S MANUAL/INSTALLATION GUIDE DESCRIPTION OF CONNECTORS i STEREO L/R INPUT (RCA Jacks) Use a stereo RCA audio cable (not supplied) to connect stereo audio from an alternate A/V source to record using the VDH9600. o VIDEO INPUT (RCA Jack) Use an RCA video cable (not supplied) to connect video signals from an alternate A/V source to record using the VDH9600. p DC IN 12V (4-Pin Molex) Use the supplied dc power cord (with cigarette lighter end) to connect the VDH9600 to the vehicle's 12-volt electrical system. Figure 2. The VDH9600's rear connections. y STEREO L/R OUTPUT (RCA Jacks) Use a stereo RCA audio cable (not supplied) to connect stereo audio from the VDH9600 to the Video Tuner or A/V source switcher. a REMOTE SENSOR INPUT (3. 5 mm Plug) Install and connect the remote mount IR Sensor (included) to the back of the VDH9600 when the player is hidden away or mounted under a seat. u VIDEO OUT (RCA Jack) Use an RCA video cable (not supplied) to connect video from the VDH9600 to the Video Tuner, Monitor, or A/V source switcher. VDH9600 VIDEOCASSETTE PLAYER/RECORDER DESCRIPTION OF REMOTE CONTROL 3. Slide the battery holder back into the remote until it locks with a "click". Description of Remote Eye The VDH9600 is supplied with a Remote Eye sensor which allows you to access all the features on the credit card sized Remote Control when the VDH9600 is mounted in another location away from the front panel sensor opening. Simply plug the sensor cable into the rear of the VDH9600. Run the sensor and cable to the front of the vehicle and mount the sensor in a convient location. NOTE: The IR sensor mounted in some Clarion monitors, such as the VMA6491, can be connected directly to the remote sensor input to function as the remote eye for the system. Battery Installation of VDH9600's Remote Control. Inserting Battery Into The IR Remote Control 1. Locate the battery compartment on the back of the IR Remote Control. Remove the battery holder and insert one CR2025 battery (supplied), matching polarity as shown on the battery holder (positive side up). 8 Figure 4. VDH9600 Remote Eye. OWNER'S MANUAL/INSTALLATION GUIDE Using The IR Remote Control Inside the vehicle, simply aim the Remote Control directly at the VDH9600's faceplate and press any desired button. When direct line of sight is impossible, install the remote mount IR sensor in the front of the vehicle. For best results, also note the following: · Aim the Remote Control from no further than 7 feet away and no more than 3 feet on either side of the VDH9600 faceplate or remote mount sensor. · Direct sunlight or very bright light will reduce sensitivity to remote signal commands. Be sure the remote sensor is not located in direct sunlight. · Objects between the VDH9600 faceplate or the remote mounted IR sensor will interfere or block IR remote signal commands. DEW/HEAT SENSOR OPERATION inhibit the drive section to avoid damaging heads due to sticking tape or high internal temperatures that can cause tape damage. The unit will be powered on, but it will not accept a videocassette. NOTE: If a videocassette was left in the VDH9600, press EJECT to avoid damaging the tape during this procedure. If moisture is the problem, leave the power on so the unit can warm up and dry any accumulated moisture. When the Dew/Heat Indicator stops flashing, the unit will return to full operation. HEAD CLEANING The VDH9600 is equipped with a built-in Dew/Heat circuit that automatically detects for moisture condensation and internal temperature. When activated, the DEW/HEAT Indicator will flash red and the Dew/Heat Sensor circuit will Over time the picture may become blurred, interrupted, or noisy. Probably dirt has accumulated on the video heads and the unit will require cleaning. You can verify this symptom by playing several different videocassettes. If the problem is the same, then the heads need to be cleaned. [. . . ] Videocassette sounds mono. Videocassette Play a videocassette recorded by stereo that has a Hi-Fi recorder in mono. Unit is set to mono Use Remote buttons in Audio Output to change audio mode. modes (see page 11). 16 OWNER'S MANUAL/INSTALLATION GUIDE SPECIFICATIONS General Specifications Audio Output: Video Input: 12 volts dc 10 watts, Power On 0. 15 watts, Power Off 5. 3 lb (2. 4 kg) 10. 5 x 3. 64 x 10. 5 in. (265 x 92. 5 x 265 mm) Remote Control, (1) CR2025 (3V) and Power Cable (with Cigarette Lighter Plug) VHS Standard NTSC 0. 498 in. [. . . ]