User manual CLARION VMA6491

[. . . ] 9 1 VMA6491 6. 4" TFT LCD Monitor PRECAUTIONS: · This monitor is intended for use in DC 12V, negative ground vehicles. · Do not operate the monitor in ways other than described in this guide. Doing so may cause damage and void the warranty. · Be careful not to run down the car's battery while using a multimedia system with the engine stopped. Doing so may damage the vehicle's battery or the multimedia system. · Do not disassemble or modify the monitor. [. . . ] Once a location has been determined, run the 3. 5 mm IR extension, Video RCA and Power molex connector into the monitor's mounting location. Mount the monitor using four (4) M4x8 mm machine screws (machine screws are provided with the mounting brackets). Run the IR extension, video, and power cables to their respective destinations. When using the VDH9600 and TTX001 together, make all of your connections near the VDH9600 (see the figure on page 5 for more details). INSTALLATION 4 OWNER'S MANUAL APPLICATIONS: (With the VDH9600, TTX001 and the FM100S) 1. Pick a location to mount the TTX001 TV tuner. Typically the tuner is located close to the VCR player. Avoid areas with excessive heat or moisture. 2. Mount the TV antenna (ZCB-303 or equivalent) and plug it into the TTX001 antenna input connector. Plug the 16-pin A/V Output and 2-pin Power Molex connector into the TTX001 tuner. Using the supplied A/V cable, connect the Left (white), Right (red), and Video (yellow) RCAs into their corresponding LINE IN locations on the back of the VDH9600. Connect the IR extension cable from the TTX001 into one of the jack inputs on the 3. 5 mm mono Y-connector (not provided). Connect the plug side of the Y-connector to the REMOTE SENSOR INPUT on the back of the video play- 5 APPLICATIONS VMA6491 6. 4" TFT LCD Monitor er. Connect the other jack end of the Y-connector into the IR extension cable coming from the VMA6491 monitor. Plug the video RCA from the VMA6491 into the LINE OUT video connection on the rear of the player. Plug the provided audio RCA cable into the L/R LINE OUT audio connections. Connect the power wires from the VMA6491, TTX001, and the power wires of the VDH9600 together. Run both the audio RCAs and power wires to the radio location and plug the audio RCAs into the FM100S audio inputs. Mount the switch for the FM100S and run its' power wire to the radio location. The power wires of the TTX001, video player, VMA6491 and the FM100S can be joined and connected to the radio accessory and battery wires. Plug the vehicle antenna into the antenna input of the FM100S. Plug the antenna output of the FM100S into the radio. The FM100S has a two position switch used to select the modulation frequency (88. 7 or 89. 1 Mhz). [. . . ] The TV picture is now displayed on the monitor. Turn on the IR headphones with its power switch to listen to the audio, adjust the volume level on the head phones to a comfortable level. 7 VMA6491 6. 4" TFT LCD Monitor DESCRIPTION OF RC300 REMOTE BUTTONS: 1 Number Pad 2 Skip 3 Erase/Write 4 Volume Up 5 Volume Down 6 TV/Video 7 Power 8 Channel Up 9 Mute 0 Channel Down q Picture Select w Auto Memory e TV/CATV BATTERY INSTALLATION: · Insert 2 AAA batteries into the compartment located on the back of the unit, observing the proper polarity. NOTE: Each time the batteries are changed, the remote channels must be reprogramed. Use alkaline batteries; do not use rechargeable batteries. Always change all the batteries at the same time. RC300 REMOTE OPERATION: · To use the remote control, press the Power button to turn on the remote. [. . . ]