User manual CLARION WH105 INSTALLATION MANUAL

[. . . ] CLARION DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY, INCLUDING FATALITIES, OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED USES OF THIS PRODUCT. ABOUT INSTALLATION Installation of mobile audio and video components requires experience with a variety of mechanical and electrical procedures. Even though this manual provides general installation and operation instructions for your new Clarion WH105 RF Headphones, it does not show the exact installation methods for your particular vehicle. If you do not have the required knowledge and experience to successfully complete the installation, we strongly recommend consulting an authorized Clarion dealer about professional installation options. . 2 . 3 . 4 . 4 . 5 . 5 . 6 . 7 . 7 . 7 . 7 . 8 1 Introduction The Clarion WH105 is a full-featured, high-tech Wireless Automotive RF Stereo Headphone System specifically created for the mobile environment. [. . . ] Volume Control Allows user to set individual listening levels. 6. Auto ON/OFF Micro Switch Turns the headphones ON when placed on the user's head and turns OFF the headphones when removed. 3 Description Of RF Transmitter Box RF Wireless Automotive Transmitter 1. Power Input 2. RCA Plug (Left Channel) 3. RCA Plug (Right Channel) 4. Power ON/OFF Switch 5. Channel Select Switch (Channel 1, Channel 2) 6. Antenna Cord RF Transmitter Specifications General Specifications Power Requirement: Power Consumption: Frequency Response: Distortion: Dimensions (W x L x H): 12 Vdc 1 watt, Power On 35-12KHz 0. 8%-1. 5% 62 x 103 x 26mm 4 Battery Installation 1. Open the battery compartment by sliding the cover towards the bottom of the Headphone. Place two (2) alkaline AAA batteries into the battery compartment of the Headphone(s), making sure that the battery polarity is correct. Snap the battery cover back into place. Operation Description PLEASE READ CAREFULLY TO PREVENT DAMAGE TO THE HEADPHONES OR YOUR EARS. Be sure batteries are properly installed in the Headphones. Turn the Headphone volume nearly off before turning on the power switch. Turn the Headphone power switch to the ON position. Adjust the Headphone volume to a comfortable listening level. (You can adjust the audio source volume louder if needed). 5 INSTALLATION Precautions Do not allow liquids or foreign objects to enter the WH105 RF Transmitter or Headphones. If any unit should become wet, turn off all power and let your authorzied Clarion Dealer clean or service the equipment. DO NOT ATTEMPT TO OPEN OR SERVICE THE RF TRANSMITTER OR HEADPHONES. THE INTERNAL PARTS ARE NOT USER-SERVICEABLE. Do not drop or excessively jar the WH105 headpones. Do not use liquid cleaners on any surfaces. Only use a soft (cotton or other non-static) cloth to wipe off fingerprints. Do not subject the unit to direct sunlight or an extremely hot environment (e. g. , closed windows on a hot summer day, direct path of heater vent, etc. ) Avoid using the products under the following contitions: - After extended parking on an extremely hot or cold day - Near strong magnetic fields - In an environment with excessive humidity, dust, or vibration (e. g. , off-road travel, etc. ) 6 Wiring This unit operates on an automotive 12-volt negative ground power source and requires additional mobile audio and video components for proper operation. Before installation, disconnect the (-) negative lead from the vehcile's battery. Attach the RF Transmitter to a location near your A/V Source with the provided adhesive tape. Connect the power and ground wire connectors to the 12Vdc input. [. . . ] The signal on one channel may be louder than the other, resulting in possible hearing damage. 7 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in an automotive installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ]