User manual CLARION XMA2

[. . . ] 9 1. PRECAUTIONS This equipment has been tested and found to comply with Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] OPERATION Note: · Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3. Basic Operations CAUTION When this unit is turned on, starting and stopping the engine of a boat with its volume raised to the maximum level may harm your hearing. Be careful about adjusting the volume. Setting the Clock 1) While pressing the BAND button #, press the DISP button 4 to enter the clock display mode. 2) While pressing the BAND button #, press and hold the DISP button 4 for 2 seconds or more. This enables the clock editing mode. The editable fields will be indicated when the display flashes. IMPORTANT Door must be totally closed to prevent water go into the set! 3) To move between the hour and minute fields, use the left (hour) and right (minute) buttons !. 4) To store the clock setting, press the BAND button #. Notes: · If you select another operation mode before completing the above procedure, the clock setting operation will be canceled. · Removing the vehicle's battery for a check or repair will cause the clock to reset to 1:00. Set the clock again if this happens. Tape Operation OK NG Loading Tapes Open the door by push the hook. 1) Press the POWER button 2. To turn the power off, press the POWER button for at least 1 second. 2) Press the FUNC button 2 to select another operation mode. The mode switches as follows each time the FUNC button is pressed: Radio Tape Radio "CASS" appears when no tape is loaded in the unit. 3) Use the Up and Down buttons 1 to adjust the volume. z: Decreases the volume. Audio Mode Adjustments 1) Press the A-M button @ to select the adjustment mode. The mode switches as follows each time the A-M button is pressed: BASS/TREB BAL/FAD Previous mode 2) Use the Left and Right and the Up and Down buttons !, 1 to adjust the bass and treble. <Adjusting the bass> d: Bass gets stronger. <Adjusting the treble> w: Treble gets stronger. 3) Use the Left and Right and the Up and Down buttons !, 1 to adjust the balance and fader. <Adjusting the balance> d: Sound from right speakers gets stronger. a: Sound from left speakers gets stronger. <Adjusting the fader> w: Sound from front speakers gets stronger. z: Sound from rear speakers gets stronger. Insert the cassette tape into the Cassette insertion slot with the side on which the tape is exposed facing the right. Playback starts automatically. When the end of the cassette tape is reached, the auto reverse mechanism is activated and the other side of the tape begins playing automatically. Note: · Fully insert the cassette tape into the cassette insertion slot. Listening to a tape which is already loaded Press the FUNC button 2 to select the tape mode. Playback begins automatically. Ejecting Cassette Tapes Open the door by push up the hook. The cassette tape is ejected. The radio mode is selected automatically 4 seconds after ejecting the tape. Fast-Forwarding and Rewinding Use the FF button 8 and REW buttons 6. A: Press this to rewind the tape. Switching the Display While pressing the BAND button #, press the DISPLAY button 4 to enter the clock display mode. [. . . ] The band changes as follows each time the "BAND" button is pressed: FM1 FM2 FM3 AM FM1 3) Use the corresponding Preset buttons 5 to select the desired station. Seek Tuning 1) Press the "BAND" button # and select the desired band. 2) The seek tuning mode is selected when "SRCH" is illuminated on the display. Seek tuning automatically stops when a station is found. Manual Tuning 1) Press the "BAND" button # to select the desired band. 2) Press and hold the "BAND" button for more than 2 seconds. [. . . ]