User manual CLASSE AUDIO CAM-200

[. . . ] 8 PROTECTION CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 CAM200 BACK VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 CAM200 TOP VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] PLEASE MAKE SURE YOU HAVE PREVIOUSLY HOOKED UP THE SPEAKERS AND PREAMPLIFIER TO YOUR AMPLIFIER BEFORE CONNECTING THE AC POWER CORD TO THE AMPLIFIER. CAUTION: SAFETY INSTRUCTIONS DISCONNECT AC LINE CABLE WHILE MAKING ALL CONNECTIONS. "FLOATING THE GROUND", OR DEFEATING THE GROUND ON A 3-PRONG LINECORD MAY CREATE A SHOCK HAZARD. CONNECT ALL INTERCONNECT CABLES BETWEEN THE ELECTRONICS BEFORE CONNECTING THE A. C. THIS WILL REDUCE THE POTENTIAL SHOCK HAZARD. Input and output connectors are clearly marked on the back of the amplifier. Use only high quality interconnect and loudspeaker cables, and make all connections tight. If the RCA input plugs are loose, remove them and pinch down the ground leaves slightly with pliers. Observe correct phasing of the loudspeaker connections, and tighten. Caution: 1) Do not over tighten the output connectors as this can result to damage your unit. 2) Do not use speaker system that has common ground with this amplifier. IR OUT and IN 5 The CAM200 can be turned ON /OFF using a +5VDC trigger or with remote control code via the IR IN jack located at the rear of the unit. The IR OUT is the loop out of the incoming signal from IR IN. The IR OUT has it own buffer to isolate between IN and OUT. Your CAM200 is factory set as being the 1st amp (AMP 1) to be turned on in sequence. To reprogram your unit so that it would be the 2nd, 3rd, 4th, 5th or 6th amps to be turned on in sequence you have to follow this procedure. J3 X X X X X X X X out out out out out out out out J2 X X X X out out out out X X X X out out out out J1 X X out out X X out out X X out out X X out out J0 X out X out X out X out X out X out X out X out ADDRESS 0 1 2 3 4 5 0 0 0 1 2 3 4 5 0 0 RC Button Amp 1 Amp 2 Amp 3 Amp 4 Amp 5 Amp 6 Amp1 Amp 1 DC DC DC DC DC DC DC DC Auto ON No No No No No No No Yes No No No No No No No Yes Note Default setting Turn on when AC is live DC level: 5v=on, 0=off ON as plug in IR OUT and IN (Continued) 6 The remote control system is RECS80 with the system code 5 and the command codes is as follows: AMP1 _____ 24 AMP2 _____ 25 AMP3 _____ 26 AMP4 _____ 27 AMP5 _____ 34 AMP6 _____ 35 These command codes will toggle the CAM200 ON/OFF. To turn all six of the amplifier ON and OFF the following code should be used: ALL ON_____08 ALL OFF_____9 CONNECTIONS FOR REGULAR OR BALANCED INPUTS: 7 The CLASSÉ CAM200 power amplifier is equipped with both regular and balanced inputs, either one may be used SEPARATELY, BUT NOT SIMULTANEOUSLY. Be sure that the CAM200 is OFF before changing any connections. When the amplifier is shipped from Classé, there is a jumper at the balanced input (XLR) between pin 1 and 3. To use the amplifier in single ended mode simply connect a single ended interconnect from the preamplifier to the RCA input of the CAM200. To use the CAM200 in balanced mode, remove the single ended interconnect and remove the jumper at the XLR; please keep this jumper for later use; connect the preamplifier to the CAM200 using balanced interconnect. The XLR connector of the CAM200 is configured as below PIN 1: DRAIN PIN 2: POSITIVE (NON-INVERTED) SIGNAL, "HOT" PIN 3: NEGATIVE (INVERTED) SIGNAL All Classé preamplifiers and amplifiers have the same pin out configuration of the XLR. Other manufacturers may have different XLR pin out configuration please contact the manufacture if you wish to maintain absolute phase throughout your system when connect Classé's equipment with other manufacturer's equipment. Having confirmed or established the correct phasing, be sure the amplifier is off, then plug the XLR connector of the balanced interconnect into the locking XLR connector on the rear panel of the CAM200. [. . . ] True symmetrical, differential amplifier circuits from input to output. Thick brushed Soft Shadow Silver faceplate with Satin Black middle plate. CAM200 SPECIFICATIONS: Frequency response: Sensitivity: Input Impedance: Output Impedance: Gain: S/N Ratio: THD+N: Rated Output: 8Ohms: 4 Ohms: Dimensions: Gross: Net: Weight: Gross: Net: 200Watts 400Watts 25" x 16" x 19. 5" 11. 5" x 16" x 9. 5" 52 lbs. 20 Hz to 20 kHz +/- 0. 1 dB 1 Volts in for rated output 75 Kohms 0. 017 Ohm 29. 02 dB 135 dBR 0. 004% 13 Notice to all Classé Product owners: Thank you for your purchase of a Classé Audio component. [. . . ]