User manual CLIFFORD 12.5X

[. . . ] Model 12. 5X O Owner's Guide limited lifetime consumer warranty Directed Electronics ("Directed") promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone number and address; the authorized dealers name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. This warranty is non-transferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. [. . . ] Doors are covered by NPC® differently; if the alarm is triggered by an open door for three full cycles, the doors will be bypassed until the trigger ceases. note: Arming and disarming the system does not reset this function. In order to reset a bypassed zone, the same zone must not trigger for 60 minutes, or ignition is turned on. If testing your system, it is important to remember that the NPC® programming can cause zones to be bypassed and appear to stop working. If five chirps are heard when disarming, NPC® has been engaged. If you wish to clear the NPC® memory, turn the ignition key on. NPC® is On/Off programmable. See your dealer and the Programming section of this guide for more information. 28 © 2006 directed electronics auxiliary outputs (options) This system also supplies outputs that can control convenience options such as remote control trunk release and window automation. Consult your dealer for available options for your system. Channel 2 Trunk release: When connected, pressing seconds will remotely release the vehicle trunk lid. Channel 3 auxiliary output: When connected, pressing will immediately activate this output to control an additional convenience option. Channel 4 auxiliary output: When connected, pressing will immediately activate this output to control an additional convenience option. Channel 5 auxiliary output: When connected, pressing will immediately activate this output to control an additional convenience option. Channel 6 auxiliary output: When connected, pressing or will immediately activate this output to control an additional convenience option. The remote will respond with a page notification consisting of one long beep and for 4-seconds displays the channel number on the LCD screen. This occurs at the remote after the system has received the command to activate any of the Auxiliary outputs. and and and and for 1. 5 © 2006 directed electronics 29 shock sensor adjustment To enter shock sensor adjustment mode: note: The system must be disarmed, and doors and other protected entries (zones 1 and 6) must be closed, and ignition (zone 5) must be off. 1. Press and hold and buttons for 4-seconds. 2. The siren will emit one long chirp and LCD remote will emit 1 long beep when the buttons on the remote are released (or 1 vibrate, or 1 long beep with vibrate) to indicate entry into shock adjustment mode. The word "SENSOR" on the LCD transmitter above the adjustment indicator bar will flash for the duration of shock adjustment mode. The sensor bar indicator will display the current sensor sensitivity setting. Increased sensitivity is indicated as the bar fills to the right. note: The LCD transmitter will also have the zone 2 icon and the alarm icon indicating. 4. The in vehicle LED will illuminate continuously for the duration of shock adjustment mode. note: When the shock sensor adjustment mode is entered, all other timers and operations are bypassed until shocksensor adjustment mode is exited. 30 © 2006 directed electronics Adjusting the Shock Sensor Setting note: When adjusting the shock sensor, ensure that the vehicle's doors are closed. 1. Increase Sensitivity--Press and release the button to increase shock sensor sensitivity by one step. [. . . ] Your system is ready for this feature, however installation may require additional labor. Input: A physical connection to the system. An input can be provided by a sensor, pinswitch or through an existing system in the vehicle, such as ignition or courtesy lights. In-vehicle status LED: A light mounted somewhere in the vehicle. It is used to indicate the status of your system. It is also used to report triggers and faults in the system or sensors. LCD: This is a Liquid Crystal Display used on your remote trans- mitter to display your vehicles status/alarm information. Shock Sensor: This is a sensor mounted in the vehicle that is designed to pick up impacts to the vehicle or glass. Siren: Noise generating device usually installed in the engine compartment of the vehicle. It is responsible for generating the © 2006 directed electronics 53 "chirps" you hear, as well as the six tones you hear while the alarm is triggered. Transmitter: Hand-held, remote control which operates the various functions of your system. Trigger or Triggered Sequence: This is what happens when the alarm "goes off" or "trips". [. . . ]