User manual CLIFFORD 50XUK

[. . . ] World-Class Auto Security TM concept 50x Owner's Manual n PLEASE NOTE: Your factory-set 4-digit valet code is noted below. See pages 10-11 for information on using your valet code: n If you wish to change your valet code to a different 4-digit number, please refer to the example on page 11. Write your new valet code in the space below: WARNING: For security reasons, do not keep this manual in your vehicle (since a thief could possibly access it and learn of your secret valet code). As such, please keep this manual in a safe place in your home. Concept 50x is covered by one or more of the following Clifford Electronics U. S. A. [. . . ] In such a case, the system will revert to the previous code. Remote controlled valet mode entry and exit You can even remotely enable or exit valet mode by transmitting channel 9 (LevelShift twice, then button 1). In addition to the above indications, two indicator light flashes confirm remote enabling of valet mode, a single flash confirms exiting. The next time that the ignition switch is turned to the "ON" position, valet mode is automatically exited. 11 Keyless entry in valet mode Even if valet mode is enabled, you can still remotely control the convenience features. For instance, press button 1 (channel 1) as if you were disarming: the doors will unlock (confirmed by one indicator light flash) and the interior lights will turn on. Press button 1 again and the doors lock (confirmed by two flashes). You can also use the other channels to activate options such as a remote boot release or remote engine starting. Sensor adjustment The two zones of your Concept 50x's Proximity Sensor provides dual-level protection of your vehicle. If someone is lurking near your car, perhaps bringing their hands and face to the window to see what is inside, the outer zone of the sensor will pick up this nearby movement and trigger your Concept 50x to issue its warning tone. But if a thief actually leans into the passenger compartment, the sensor's interior zone will be triggered and the system will instantly blast the full alarm sound. The Clifford Electronics Proximity Sensor is a radar-type sensor that uses a more sophisticated, more accurate and more reliable technology than that of ultrasonic-type movement sensors. As such, the Dual-Zone Proximity Sensor of your Concept 50x is impervious to normal environmental conditions such as wind and temperature variations that cause ultrasonic sensors to false alarm. Your Authorised Clifford Dealer will have adjusted each of the two sensor zones at the time of installation. If you find that the sensitivity setting of one or both appears to be a bit off the mark, any local Authorised Clifford Dealer will be happy to make any necessary readjustments without charge. Remote controlled override of one or both sensor zones Transmitting channel 10 (two presses of the side LevelShift button, then a press of button 2) within 10 seconds of arming the system will override the exterior warning zone of the Dual-Zone Proximity Sensor. When you do so, you will see 4 indicator light flashes to confirm the zone override. This is useful when parking in an area with heavy pedestrian traffic. Transmitting channel 10 again within the 10 second period will override both zones of the sensor for those times when you must leave a passenger or pet in the vehicle. The sensor zones are automatically restored the next time you arm the system. AutoLock and AutoUnLock For your safety and that of your passengers, the doors automatically lock the instant you turn on the ignition (see User-selectable features on pages 16-20). When you turn the ignition off, AutoUnLock automatically unlocks the doors. To suit your preferences, you may turn off either or both the AutoLock and/or AutoUnLock features. 12 Built-In Two-Point AutoImmobiliser Thirty seconds after you turn off the ignition, the system's built-in two-point AutoImmobiliser electronically disengages your vehicle's starter motor and electronic fuel pump to ensure against theft of your vehicle. The LED Status Indicator will repeatedly flash to indicate that AutoImmobilisation has been activated. [. . . ] Should any fault with the security system occur, please contact your installing Clifford agent as soon as is convenient. 18 Table of user-selectable features: 1 chirp = OFF, two chirps = ON. Feature Select Row 1 1st momentary Row 2 2nd momentary Row 3 3rd momentary Row 4 4th momentary Row 5 5th momentary Row 6 6th momentary Column 1 1st latched Add new remote to channel 1 NOTE 1 Add new remote to channel 2 NOTE 2 Add new remote to channel 3 NOTE 3 Add new remote to channel 4 NOTE 4 Erase all channels NOTE 5 Column 2 2nd latched AutoLock on/off AutoUnLock on/off FACT: on/off AutoActivate timed channel 4 accessory upon remote arming: on/off this feature is for installers only QuietChirps: on/off Long-term chirp silencing: on/off Column 3 3rd latched AutoArming: on/off AutoArm & Lock: on/off NOT USED D Set accessory timer duration: 1sec - 2min (30sec) NOTE 6 NOT USED Set a new secret valet code NOTE 7 NOT USED D WARNING: If you have remote window and sunroof closure, DO NOT CHANGE THIS SETTING: it requires installer-only adjustment. DO NOT alter the installer-only setting in the grey cell. There is also an installer-only column 5, so if you accidentally select an installer-only feature, turn off the ignition and start again. n n n n n n NOTE 1: Transmit channel 1 (or other channel of your choosing) of the new remote control. [. . . ]