User manual CLIFFORD INTELLIPAGE

[. . . ] World-Class Auto Security TM IntelliPage Owner's Manual The IntelliPage system is covered by one or more of the following Clifford Electronics patents: 4, 158, 874; 4, 233, 642; 4, 327, 444; 4, 383, 242; 4, 430, 685; 4, 845, 464; 4, 887, 064; 4, 890, 108; 4, 922, 224; 4, 997, 053; 5, 081, 667; 5, 146, 215; 5, 157, 375, 5, 467, 070 and other patents pending. WARNING The IntelliPage system is designed to be used ONLY on a fuel-injected, gasoline or diesel powered vehicle with an automatic transmission. Installing an IntelliPage on a vehicle that has a manual transmission poses an EXTREME SAFETY RISK!Never install a Clifford remote engine starting product on a manual transmission vehicle. Always exercise good judgment and common sense when using the remote starter: · NEVER remotely start the vehicle in an enclosed area without sufficient ventilation. · NEVER allow children access to the remote controls. [. . . ] Proximity Sensor warning zone: Lean toward the driver's window. You'll hear a chirp when the zone detects your presence. Ideally, it should chirp only when you move within one foot of the vehicle, as a thief would do to see what was inside. Piezo Sensor alarm zone: Firmly "thump" the top of the window pillar. You will hear a chirp if the strike was firm enough to trigger the alarm zone of the sensor. Piezo Sensor warning zone: "Thump" the top of the window pillar with somewhat less force than noted above. You will hear a chirp if the strike was firm enough to trigger the warning zone of the sensor. If you are not satisfied with the detection level and wish to increase sensitivity, press button 2 on your remote control. Each time you increase sensitivity, the siren will chirp in higher and higher pitched tones to confirm the higher sensitivity setting. Conversely, lower and lower tones confirm each sensitivity decrease. Three normal tone chirps indicate minimum and maximum settings. There are 32 sensitivity levels for each of the Proximity Sensor's two zones; the alarm zone of the Piezo Sensor also has 32 levels, while the less critical warning zone has 16 steps. Repeat steps 2 and 3 until you are satisfied with the sensitivity, then press button 1 to record the new sensitivity setting and exit the sensor test/adjust mode (you'll hear three chirps to confirm exit). You may now either repeat steps 1­4 for the other sensor and/or sensor zone, or press button 1 again to arm the system. It really isn't, there's just a lot of explanation of what's happening with each step. All you really have to do is the actions noted in bold type. Give it a try. Remote controlled override of one or both sensor zones Transmitting channel 10 within 10 seconds of arming the system will override the exterior warning zone of the Proximity Sensor (you'll see 4 parking light flashes to confirm the zone override). This is useful when parking in an area with heavy pedestrian traffic. Transmitting channel 10 again within the 10 second period will override both zones of the sensor for those times when you must leave a passenger or pet in the vehicle. The sensor zones are automatically restored the next time you arm the system. How to interpret the LED status indicator The LED on your car's dashboard or console will inform you of the system status: LED Condition Off On Flashing Pause between flashes Meaning System is disarmed and in normal operating mode (i. e. , valet mode is off) Valet mode is on, the vehicle can be driven or serviced without having to disarm System is armed and protecting your vehicle Either a malfunction occurred or an intrusion was attempted (see pages 24-25) Automatic battery-saving mode To conserve vehicle battery power (the LED draws more current than the entire control unit) if the system has remained continuously armed for 48 hours, the flash rate will automatically slow to half the normal rate. After 96 hours, it slows to one-quarter. 22 NightVisionTM All of the following NightVision Headlight Automation features are built into your IntelliPage: n User-selectability: You may turn the NightVision features on or off whenever you wish (see User-Selectable Features on pages 35-39). n When driving at dusk: The system automatically turns on the headlights. [. . . ] After about 10 seconds you will hear 4 rapid chirps, indicating that all user-selectable features except the valet code and remotes have been reset to their factory settings. 37 Table of user-selectable features: 1 chirp = OFF, two chirps = ON Feature Select Row 1 1st momentary Sound 1: on/off info on page 26 Sound 2: on/off info on page 26 Sound 3: on/off info on page 26 Sound 4: on/off info on page 26 Sound 5: on/off info on page 26 Sound 6: on/off info on page 26 Erase all channels info on page 26 NOTE 2 Add new remote to channel 5 info on page 15 NOTE 1 QuietChirps: on/off info on page 26 Long-term chirp silencing: on/off info on page 26 Add new remote to channel 4 info on page 15 NOTE 1 AutoActivate channel 4 timed accessory upon remote arming this feature is for installers only Add new remote to channel 3 info on page 15 NOTE 1 FACT: on/off info on page 23 Add new remote to channel 2 info on page 15 NOTE 1 AutoUnLock: on/off info on page 25 Add new remote to channel 1 info on page 15 NOTE 1 AutoLock: on/off info on page 25 AutoArming: on/off info on page 18 AutoArm & Lock: on/off info on page 18 15-second entry delay: on/off info on page 18 AutoStart: battery mode/ temperature mode/dual mode/off (2/3/4/1 chirps) NOTE 3 Siren duration: 60/30 seconds (1/2 chirps) info on page 26 Set a new secret valet code info on page 20 NOTE 4 Column 1 1st latched Column 2 2nd latched Column 3 3rd latched Column 4 4th latched Column 5 5th latched Column 6 6th latched NightVision: off/on but no post-parking illumination/on (1/2/3 chirps) info on page 23 Use this remote to activate which memory seat position?info on page 20 NOTE 6 Row 2 2nd momentary Row 3 3rd momentary Row 4 4th momentary Row 5 5th momentary Row 6 6th momentary Post-parking and remote headlight Door ajar warning/delayed duration: 1sec­2. 0min (30sec) courtesy lights info on pages 15 and 23 NOTE 5 this feature is for installers only SilentNight: on/off info on page 23 RPM-activated AutoLock: on/off info on page 25 D Channel 4 timer: 1sec-2. 0min (30sec) info on page 15 NOTE 5 RPM programming this feature is for installers only Channel 4 output type: Lock pulse duration: 3sec/1sec pulsed/timed/latched this feature is for installers only this feature is for installers only NOT USED Diesel/gasoline fuel injection this feature is for installers only D WARNING: If the system automatically closes the power windows and sunroof when you remotely arm, DO NOT CHANGE THIS SETTING: It requires installer-only adjustment. Changing the duration may cause damage. The gray cells indicate features that requires programming only by a qualified installer. DO NOT change installer-only settings -- damage to the system or your vehicle may result. NOTE 1: Transmit the appropriate channel of the new remote control. [. . . ]