User manual CLIFFORD SOLARIS

[. . . ] The Science of SecurityTM SOLARIS Complete Owner's Manual USA Headquarters 20750 Lassen Street Chatsworth, California 91311 1-800-CLIFFORD or 1-800-824-3208 or 1-818-709-7551 Canada Headquarters 4513 Dobrin Street Montreal, Quebec H4R 2L8 1-800-361-3444 or 1-514-332-4444 UK Headquarters Boundary Business Court 92/94 Church Road Mitcham, Surrey CR4 3TD 0800 929949 or 0181 646 8440 Germany Headquarters Schlesische Straße 27 10997 Berlin 0130 115 681 oder 030 611 2602 Mexico Headquarters Saratoga 804 B, Col. Benito Juárez 03300 México D. F. 01 800 021 2543 o 5 605 0382 Clifford systems are covered by one or more of these Clifford Electronics USA patents: 4, 158, 874; 4, 233, 642; 4, 327, 444; 4, 383, 242; 4, 430, 685; 4, 845, 464; 4, 887, 064; 4, 890, 108; 4, 922, 224; 4, 997, 053; 5, 081, 667; 5, 146, 215; 5, 157, 375; 5, 467, 070; 5, 650, 744 and other patents pending Always exercise good judgment and common sense when using the remote starter: · NEVER remotely start the engine if parked in an enclosed area lacking sufficient ventilation. · NEVER allow children access to the remote controls. [. . . ] On the master remote, press the LevelShift three times, then button 3. You will hear one chirp and the LED will turn on. To test the primary (alarm) zone, press button 4 (you will hear a chirp confirmation), then firmly "thump" the top of the A-pillar (the area between the side windows near the roof) heel of your fist. If the impact is strong enough to trigger the primary zone, you will hear a siren chirp. To change sensitivity, press button 4 to reduce sensitivity, button 2 to increase sensitivity. Two chirps will acknowledge each sensitivity increase, one chirp will confirm each decrease. You can test the new setting by again thumping the top of the A-pillar. You may now press button 3 to adjust the warning zone (as noted in 3a. below), or press button 1 to fully exit the sensor adjustment mode (you will hear 3 chirps). For the Piezo Sensor warning zone, press button 3 (you'll hear 1 chirp). Then use the same procedure as above, but thump less forcefully for the warning zone. When done, press button 1 to reselect the primary zone (you will hear 2 chirps), then button 1 again to fully exit sensor adjustment mode (you will hear 3 chirps). User-Selectable Headlight Reminder You can set your system to issue a warning tone if you attempt to exit the vehicle without turning off the headlights. Since many vehicles already have a similar feature, or have delayed headlights, this feature is factory set to off. (Please note that this feature is not available on European models. ) % User-Selectable AutoLock and AutoUnLockTM Some vehicles are incompatible with the AutoLock and AutoUnLock features. For your safety and that of your passengers, the doors can be set to automatically lock the instant you turn on the ignition or when the engine RPMs reach about twice the idle speed, whichever you prefer. When you turn the ignition off, the doors AutoUnLock. These are user-selectable features. Smart trunk release option If you have this option, you may use the button to remotely release the trunk latch. The system's electronic interlock prevents unintentional activation of the remote trunk release when you drive, or when the system is armed. The Smart Trunk Release feature requires installer programming, so if you have the optional trunk release installed, you may want to verify that it will NOT activate when the system is armed. If it can be activated while armed, causing the alarm to sound, please return to your installing Clifford Dealer and have them correct this (it only takes a couple minutes and there will be no charge to you). High-Output Insignia Siren This Clifford-engineered siren is more rugged than generic sirens and has these features: n Remote siren silencing: If triggered by a non-threatening event, you can silence the siren without remotely disarming. Press button 1 on the master remote or button on the companion remote while the siren is sounding. Two chirps confirm that the sensor activated the alarm and the system is remaining armed. [. . . ] You must now add new/existing remotes with the "Add new remote control" feature and/or the "Other vehicle`s remote" feature. NOTE 3: Immediately PRESS THE BLANK BUTTON, THEN enter your new code, wait for the two chirps, then turn off the ignition (you'll hear 3 chirps to confirm program mode exit). You MUST now turn the ignition back on and then re-enter your new code. If the LED flashes on, your new code has been accepted. [. . . ]