User manual COBRA ESD9570

[. . . ] Operating Instructions for Your Cobra® 11 BandTM Extra Sensory Detection® DETECTOR MODEL E S D ­ 9 5 7 0 N RADAR/LASER Nothing comes close to a Cobra ® Important Information Federal Laws Governing the Use of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra radar detector. The Communications Act of 1924 guarantees your right to receive radio transmissions on any frequency. Local laws that contravene this Act, while illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by federal court action. Safety Alert Use of this product is not intended to, and does not, ensure that motorists or passengers will not be involved in traffic accidents. [. . . ] The rev point you set will be stored in the unit's memory when power is turned off and recalled each time the power is turned on. The rev point must be reset if you use your detector in a different vehicle. Important: When initially choosing your IntelliMute activation point, a setting of approximately 300 to 600 RPMs above idle is recommended. You can reset the activation point at any time to fit your individual preferences and driving style. NW NW ih ih The factory setting is IntelliMute off. NOTE: IntelliMute may not work with some vehicles because it cannot sense the engine's revs. In such cases, you can reduce unwanted audio alerts by using Auto Mute and City modes when appropriate. Above the activation point, an arrow pointing up will appear. NW ih 10 11 3 O P E R AT I O N · S E T T I N G S O P E R AT I O N · S E T T I N G S 3 Setting the IntelliMute Activation Point Your detector must be installed in your vehicle. Caution: Do not attempt to set the rev point while driving. Your vehicle should be parked and idling. IntelliMute must be turned on. Auto Mute Mode Auto Mute will automatically reduce the audio volume of all alerts after 4 seconds for as long as the signal is detected. When you turn Auto Mute mode on or off you will hear 2 beeps for Auto Mute on and 1 beep for Auto Mute off. (See page 7 for instructions on using the Program mode to turn Auto Mute on or off) The factory setting is Auto Mute on. Muting an Alert Your detector allows you to quickly turn off an audio alert by momentarily pressing and releasing the PROG/MUTE button. If you press and release the PROG/MUTE button a second time during the alert, the audio alert will be turned back on. PROG/MUTE button Press and release 1. Procedure In Program mode, go to Set IntelliMute. Press and release the SET/CITY button to begin setting IntelliMute RPMs. Tone 2 beeps Visual Display Set IntelliMute Press SET at desired RPMs. . . Please try a Press SET a 2. Procedure Rev your engine to the level you wish to set. Rev the engine slightly above idle and hold revs steady for 2 seconds. NOTE: If the unit is unable to sense usable pulses within three seconds, IntelliMute will indicate an error and automatically turn off. Tone none 1 beep IntelliMute not set. . . Intelli Mute Off Visual Display Intelli Mute Set!Intelli Mute Off Visual Display none Intelli Mute Auxiliary Audio Jack Use to connect an external speaker in environments with high ambient noise levels. The internal speaker will be disconnected. 3. Procedure At the desired rev level, press and release the SET/CITY button. NOTE: If you do not set a rev point within 20 seconds of beginning these steps, IntelliMute will indicate an error and automatically turn off. Tone 3 beeps Off 1 beep Intelli Mute 4. Procedure Press and release either the SELECT/DIM button to proceed to the next user mode or the PROG/MUTE button to exit the Program mode. Tone none Set! 12 13 3 O P E R AT I O N · S E T T I N G S O P E R AT I O N · S E T T I N G S 3 Compass Your detector includes an internal 8-point compass that will continuously display your current direction of travel: N, NE, E, SE, S, SW, W, or NW. The compass will remain accurately calibrated as long as your detector is mounted in the same place in your vehicle. If you change the location where the unit is mounted or move it to another vehicle, you must recalibrate the compass. The compass temporarily may not provide accurate readings if you are inside a building or enclosure, or are close to a large metal tractor/trailer, truck, or train. [. . . ] Ship to: Cobra Factory Service Cobra Electronics Corporation 6500 West Cortland Street Chicago, IL 60707 USA 6. Please allow 3 to 4 weeks before contacting us about the status of your service. If your unit is under warranty, it will either be repaired or replaced upon receipt, depending on the model. If your unit is out of warranty, you will receive a letter informing you of the repair or replacement charge. 26 27 7 WA R R A N T Y S P E C I F I C AT I O N S 1 Ye Wa ar rra 8 QUALITY SEAL Cobra Electronics Corporation 6500 West Cortland Street, Chicago, Illinois 60707 USA www. cobra. com QUALITY SEAL COBRA ELECTRONICS CORPORATION warrants that its Cobra 11 Band Ultra Radar/ Laser Detectors and the component parts thereof, will be free of defects in workmanship and materials for period of one (1) year from the date of first consumer purchase. [. . . ]