User manual COBRA XRS 930

[. . . ] Introduction Important Information and · Important Information Federal Laws Governing the Use of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra radar/ laser detector. The Communications Act of 1924 guarantees your right to receive radio transmissions on any frequency. Local laws that contravene this Act, while illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by federal court action. Operating Instructions The Cobra line of quality products includes: Safety Alert Use of this product is not intended to, and does not, ensure that motorists or passengers will not be involved in traffic accidents. [. . . ] NOTE When initially choosing your IntelliMute activation point, a setting of approximately 300 to 600 RPMs above idle is recommended. You can reset the activation point at any time to fit your individual preferences and driving style. Setting the IntelliMute Activation Point Your detector must be installed in your vehicle. CAUTION Do not attempt to set the rev point while driving. Your vehicle should be parked and idling. IntelliMute must be turned on before setting the activation point. You will hear a series of beeps as you follow the steps on the next page. None Three bars will flash in succession 1 2 3 Three beeps All three bars flash three times 1 2 3 NOTE If the unit is unable to sense usable pulses within three seconds or if you do not set a rev point within 20 seconds of beginning these steps, IntelliMute will indicate an error and automatically turn Off. Tone Four beeps Visual Display E appears X K Ka V S E 11 10 English Nothing Comes Close to a Cobra® Your Detector Settings Your Detector Settings IntelliMute Pro IntelliMute Pro prevents detection by radar detector detectors (RDDs) such as VG-2, Spectre I and Spectre IV+ when traveling at slower speeds. It is intended for use by experienced users only. When IntelliMute Pro is turned On, and engine RPMs are below the IntelliMute activation point, your detector's radar detection circuits are turned Off to prevent detection by RDDs. Before IntelliMute Pro can be turned On, you must have turned On and Set the IntelliMute activation point. (See pages 9 through 11. ) CAUTION When IntelliMute Pro is On, NO radar signals will be detected and NO alerts will be given at RPMs below the IntelliMute activation point. IntelliMute Button City Button Press and hold both buttons simultaneously IntelliMute Pro On VG-2 and Spectre I & IV+ Alert Settings Police use radar detector detectors (RDDs) to spot users of radar detectors. Your detector is able to identify signals from VG-2, Spectre I and Spectre IV+ RDDs and can provide alerts when any of these or similar devices are in use near your vehicle. Your detector can be spotted by Spectre IV+ RDDs, but is invisible to VG-2 and Spectre I RDDs. You can choose whether you want to be alerted to VG-2 and Spectre I & IV+ RDD signals. The factory setting for VG-2 and Spectre I & IV+ alerts is Off. On/Off Indicator X K Ka V S c Dim Button Press and hold for four seconds To Turn VG-2 and Spectre I & IV+ Alerts On and Off While no signal is being detected, press and hold the Dim button for four seconds. Tone On = Two beeps Off = One beep Visual Display V will blink twice in the display V will blink once in the display X K Ka V S c Pop Alert The Pop Mode Radar Gun is a single-pulse Doppler radar that is a feature of a K and Ka (Bee III Ka radar gun) band Instant-On radar gun. It uses a single, short-time pulse to measure the target vehicle's speed. To Turn IntelliMute Pro On While no signal is being detected, press and hold both the IntelliMute and City buttons for four seconds. Tone Two beeps Visual Display c or h will blink The Pop mode receiver senses Pop singles beyond the effective range of Pop radar guns. As the Pop mode receiver is so sensitive, you should limit the use of Pop Detect mode to highway and rural driving. Pop Alert will alert you to Pop radar signals. During the alert, the unit continues to detect other signals. The factory setting is Pop Detect Off. To Turn Pop Alert On and Off While no signal is being Tone detected, press and Pop On = Two beeps hold both the Dim and City buttons for four seconds. [. . . ] This warranty gives you specific rights, and you may also have other rights which vary from state to state. Exclusions: This limited warranty does not apply: 1. In the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs. If the serial number has been altered, defaced or removed. [. . . ]