User manual COBY TF-DVD7500

[. . . ] DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. This Digital Video Disc player employs a Laser System. [. . . ] Note that the romote control unit may not work if there are obstacles between it and the remote sensor. Use it to locate at the beginning of previous/next tracks or chapters. Keep pressing it for about 1. 5 seconds during playback to switch playing speed of backward/forward through X2, X4, X8, X20, X2. button 3 Previous/next buttons 4 Mode button Use +/- key to adjust after entering one mode. TFT MODE: switch screen between 16:9 and 4:3. VIEW MODE: switch screen between reverse and observe. AV INPUT/OUTPUT: switch the AV function between input and output. Keep pressing the button about 1. 5 seconds to turn off the display. and press it to resume. 5 - /+ buttons Press it to adjust display mode. 6 OPEN button Press it to slide the tray out Main unit left side 1 2 3 4 5 -16- Parts and Functions 1 Phone jack For connecting stereo headphone or an amplifier. Use it to adjust the volume of the speakers or headphone. Input or output video signals to connected device by setting AV IN/OUT mode value. The included AV cable is connected here. Supply power to the player. Batter y indicator LED. 4 Player ter minals CAUTION: Do not short-circuit the terminals. -21- Connecting the Player to Other Devices Before connecting Turn off the power of the player and the devices to be connected. Connecting to a TV VIDEO IN AUDIO IN R L TV -22- Connecting the Player to Other Devices Connecting to a Dolby Digital / DTS / MPEG decoder or an amplifier with built-in decoder With this player, you can enjoy powerful Dolby Digital, DTS or MPEG sound. Output the digital signals from the player's digital output to a decoder or amplifier with built-in decoder. Main unit left panel DIGITAL IN -23- Connecting the Player to Other Devices Connecting to a digital amplifier that is not Dolby Digital / DTS / MPEG compatible Output the digital signals from the player's digital output to a digital amplifier that is not Doby/DTS/MPEG compatible. Main unit left panel Optical digital cable (not included) To digital audio input jack DIGITAL IN : Signal flow Notes: , Carefully check the player s digital output settings before connecting the player to an amplifier equipped with a digital audio input jack which is not Dolby Digital / DTS / MPEG compatible. Do not play DVDs when the audio settings are not correct. Or may cause strong noise and damage your speakers. -24- Connecting the Player to Other Devices Connecting to active speaker systems Main unit left side : VIDEO IN TV -25- Connecting the Player to Other Devices Connecting ear phone Connect the earphone' s plug securely to the PHONE JACK on the player. To listen to music through the earphone, first use the VOLUME CONTROL on the left side of the main unit to lower the volume to minimum level, then adjust the volume to comfortable level. Be careful not to set the volume to too high level when using earphone. Main unit left side VOLUME Earphone To PHONE jack Notes: Insert the headphone plug securely. No sound will be heard if the earphone is securely connected. Note: It is not possible to hear the sound of DTS-compatible DVDs over earphone. Strong noise is produced when DTS discs are played, so do not listen to such discs through earphone. -26- Using the Battery Recharging the batter y pack Recharging the battery pack as described below. 1 2 1 Connect the DC output plug of AC adapter to the batter y pack. 2 Connect the AC adapter to the power outlet. When recharging starts, the recharge LED lights in red. The recharge LED lights in green when recharging completes. Remove the power cord from battery pack. Recharging usually completes in about 4~5 hours. The battery pack can be used for about 300 cycles of recharging and operations, though this is variable depending on the operating conditions. Charge the battery pack fully before using it for the first time. CAUTION Place the battery pack and AC adapter on a flat surface for recharging. [. . . ] Remove them by gently wiping the disc from the center toward the edges using a soft cloth. Do not use damaged (cracked or warped) discs. Do not scratch the signal surface or let it get dirty. The player may be damaged if there is any exposed glue, etc. , on discs. For rental discs in particular, extra labels are often attached to the discs. [. . . ]