User manual COEF MP 300 SPOT

[. . . ] Also in case of sale, rent, change of place and/or ownership, these documents shall be enclosed with the relative equipment. ADVICES FOR A CORRECT INSTALLATION This equipment is destined to an exclusively Professional use. 1) 2) 3) 4) 5) Make sure that all the fastening parts of the spotlight are in good condition. Regulate the proportions of the fastening accessories (screws, bushes, nuts, supports, etc. ) in order to be slightly over-dimensioned as compared to the actual requirements. Carefully check the contents of the packaging and the completeness of the components. If any of the parts listed hereunder is missing, please contact your Dealer immediately. [. . . ] The lamp used in the fixture is a high pressure lamp and must be handled very carefully. The unit is realized to use only MSD 250/2 or compatible lamps; absolutely don't use other types of lamp. The lamp must be changed if damaged or deformed by heat. Wait at least 15 minutes after the projector has been switched off before operating again, in order to let it cool down and avoid the lamp explosion. Read carefully the lamp builder's instructions. Don't look directly the lamp. Wait 30 minutes in order to avoid burns. · Unscrew with a cross screwdriver the first screw A for a single turn; unscrew the second one completely B; unscrew completely the screw A and to remove the cover that supports the lampholder. · Insert delicately the lamp in the projector support, driving it with the round cover. Pay attention: the lampholder's wires must correctly reenter in the projector. · Block the cover screwing the screws up ( part. 6 3. 2 PROJECTOR INSTALLATION To fix the MP 300 Spot is necessary, when the installation has to be on a raised-from-the ground support, to block the quick lock / release brackets of the unit by means of a screw provided with nut and locknut measuring not less than M10 X 50, to insert in the central pre-arranged hole on the fixing bracket. 8 5. 0 SPECIAL FUNCTIONS AND PROJECTOR ASSIGNMENT On the front panel of MP 300 Spot you'll find a section for the additional functions and for setting the projector. Following the picture, you can see all the offered possibilities in detail. All operations are to be carried out with the E, F, G, H buttons, respectively indicated as MENU, ENTER, DOWN and UP. The display D will inform you about the selected functions. The 3 A, B and C leds will allow you to know: A = reception of the DMX line. C = errors indicated on the ERR table (see table 6. 0). On switching the projector on, the display will indicate the type of projector and the version of control software which have been installed. To this purpose, please remember that this type of projector belongs to a new generation of projectors, designed with the possibility of updating the software version through the normal DMX connection by means of a programmer deliberately created: UNI-PROG 8. After the indication MSTR HOME, the projector carries out the RESET and gets ready to be controlled from the connected console. The display will indicate 1 as default value. This means that the first channel occupied by the projector will respond to the values sent to channel 1 by the DMX line. This enables us to make MP 300 Spot (which we are installing) completely independent from control or integral with any other installed projector. General Rules: Refer to the Table of Section 6. 0 in the following page. By each pressure, Button MENU (E) permits to go backwards by one level. [. . . ] An improper use of this documentation made by not specifically qualified staff can damage irremediably the electronic and/or mechanical components of the projector. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Motor SHUTTER / STROBE Motor COLOR Motor GOBOS Motor ROTATION GOBOS Motor PRISM Motor GOBOS FIX Motor FOCUS Motor PRISM ROTATION No connect No connect Motor TILT Motor PAN Encoder TILT Encoder PAN 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Sensor PAN Sensor TILT Sensor PRISM Sensor GOBOS FIX Sensor COLOR / GOBOS / GOBOS ROT. ON / OFF Lamp Electronic ballast connector (not in use) LIGHT Sensor Power Connector Faston Ground Connection DMX IN / OUT Head FAN Base FAN Sensor FOCUS Pag. 17 11. 0 TROUBLESHOOTING - The power supply is not present - Check if the regular power supply is present on the projector. The projector doesn't swich on - The lamp is not working - The thermal switch is active - Wrong DMX configuration - Defective cables - Replace the lamp. - Just to wait for little of time. - Make sure that the projector is correctly configurated. - Replace or repair the DMX cable. The projector swiches on but doesn't answer to commands. [. . . ]