User manual CONTAX PCA 10-30A REV 0297

[. . . ] PCA 10-30A SDS SUBMERISIBLE PUMP CONTROLLER USER'S MANUAL 12/06/99 1 OPERATION AND INSTALLATION MANUAL FOR THE PCA10-30A SOLAR ELECTRIC PUMP CONTROLLER MANUFACTURED BY: GOLDEN GENESIS CO SOLARJACK 7812 E. SCOTTSDALE, ARIZONA 85260 UNITED STATES OF AMERICA PHONE # (800) 223-9580 FAX # (480) 483-6431 DC# 5223-0001-A REV 0297 For controllers with serial numbers 18057 and above Table of Contents 1. 0 Introduction 2. 0 Product Overview 2. 1 Features 2. 2 Application 3. 0 Installation and Operation 3. 1 Location 3. 2 Wiring 3. 3 Water Sensors 3. 4 Adjustment Procedures 4. 0 Troubleshooting 5. 0 Technical Specifications 6. 0 Warranty Statement 12/06/99 2 1. 0 Introduction Thank you for selecting the PCA10-30 pump controller. The PCA series of pump controllers are a high quality, solid state DC power converters designed as the interface between a Solarjack SDS series pump and a DC power source. The purpose of the controller is to maximize the total daily water output while providing protection for the pump and the DC power source as well as providing interface with other related pumping system equipment. [. . . ] Refer to sample system wiring diagrams as a guide during hook-up. 12/06/99 5 Remote Switch The Remote Switch interface can serve as an automatic system shutdown when used with a water storage tank mounted float switch. It can also serve as a manual system shutdown with a remote system ON/OFF toggle switch. The majority of installations will use this port for float switch interface. Both applications are configured and operate the same way. Please refer to the following operational scenarios for configuration options. With switch number 5 in the OFF position, the controller is configured to accommodate a Normally Open (N. O. ) float switch or remote toggle switch. In this configuration the controller will operate as follows: PUMP ON float switch open = water tank low = pump ON PUMP OFF float switch closed = water tank high = pump OFF With switch number 5 in the ON position, the controller is configured to accommodate a Normally Closed (N. C. ) float switch or remote toggle switch. In this configuration the controller will operate as follows: PUMP ON float switch closed = water tank low = pump ON PUMP OFF float switch open = water tank high = pump OFF Water Level Electrodes The water level electrodes interface serve as an automatic system shutdown when properly installed and configured. The PCA series of controllers are capable of two configurations; high or low level shutdown. The high level shutdown is typically used to interface with a water storage tank to achieve the same system control results as a float switch. The low-level shutdown is intended to monitor the well water level and shutdown the system if the water level in the well drops to a critical point. To use this interface, three E-1s brass electrodes must be used. One is for the ground (reference) , the second is for the low-level point and the third is for the high level point. Please refer to the system wiring diagrams and the following operation scenarios for configuration options. With switch number 6 in the OFF position, the controller is configured to interface with electrode water level sensors for a water level HIGH pump shutdown and a LOW water level pump activation. PUMP ON low and high level electrode exposed = water tank low = pump ON PUMP OFF low and high level electrode submerged = water tank high = pump OFF 12/06/99 6 With switch number 6 in the ON position, the controller is configured to interface with electrode water level sensors for a water level LOW pump shutdown and a HIGH water level pump activation. PUMP ON low and high level electrode submerged = well water level ok = pump ON PUMP OFF low and high level electrode exposed = well water level critical = pump OFF 3. 4 Adjustment Procedures The PCA series controllers have several adjustment features. Some are system configuration adjustments are user selectable by a six positions DIP switch located on the face of the controller. These include pre-adjusted DC source selection, remote switch selection and water level cut-off. The remaining adjustments are for input and output voltage fine-tuning that are independently adjustable by high precision multiple turn (brass screw) trimmers. The pre-adjusted DC source selection allows the user to choose the nominal input voltage and basic source configuration. These consist of four pre-adjusted voltage settings consisting of solar panel or battery in nominal 12 volt or 24-volt sources. [. . . ] Check wiring diagram for proper connection. Check for skinned wires or faulty underwater splice. With the pump out of the well, bypass the controller and connect power directly to the motor leads. If the pump still does not run and the current is over 1. 5 amps, the pump is in a locked rotor condition and just be repaired. 5. 0 Technical Specifications 12/06/99 11 6RODUMDFN V/LPLWHG:DUUDQW\ PCA 10-30A Controllers LIMITED WARRANTY ­ TWENTY-FOUR MONTHS SOLARJACK warrants the product to be free from defects in materials and workmanship under normal applications and service conditions for twenty-four (24) months from date of sale to the original purchaser, but not to exceed (30) months from the date of manufacture. [. . . ]