User manual CREATIVE SOUND BLASTER X-FI GO! PRO GUIDE DE DÉMARRAGE RAPIDE

[. . . ] Flashes green when the Connect button is pressed to indicate pairing with a wireless receiver or other supported device. 2 CO NN EC T 3 6 4 4 5 6 7 Connect button Microphone/Line In jack Headphone/Line Out jack Adjustable antenna 5 Setting Up Your Audio Device 3 Setting Up Your Audio Device Step 1: Connect to your computer's USB port OR NOTE The USB extension cradle allows you to: · Connect the audio device to your computer if it is not physically possible to connect directly to the USB port due to obstruction of neighboring USB devices. · Extend or move the audio device away from other wireless devices to optimize transmission range. Installing Software 4 Step 2: Installing Software Your audio device is operational without any software installation. However to enjoy all the features, install the drivers and applications provided on the installation CD. NOTE You can also download the software from www. creative. com/ support. [. . . ] NOTE · Clicking the Restore Defaults button in the Sound Blaster Wireless Control Panel restores the default audio settings, sets the RF channel to Auto and enables the Wireless Music Control. · Refer to your receiver's documentation for additional information. Troubleshooting 16 Troubleshooting Problems with Multiple Audio Devices The onboard audio chipset seems to be in conflict with Sound Blaster Wireless Transmitter. Disable your notebook's onboard audio chipset. See your notebook's motherboard documentation for details Problems with Sound No sound from the headphones. Check that the headphones are connected to the Headphone/Line Out jack. No audio output when playing digital files such as . WAV, MIDI files or AVI clips. Check the following: · The powered speakers or external amplifier are turned on and connected to the audio device's Headphone jack. · The speakers' volume control knob, if any, is set at mid-range. · There is no hardware conflict between the card and a peripheral device. Problems with Wireless Features The wireless connection does not seem to work. Do the following: · Check that your transmitter and your paired devices are turned on, and your transmitter's wireless features are enabled. If not, see "Using the Wireless Features" on page 11. · In case of configuration issues, you can fully reset your wireless system by clicking the Reset all Zones button in the Sound Blaster Wireless Control Panel, and then manually pair your receivers again. Troubleshooting 17 The receivers seem to be picking up extra noise, or there are intermittent pauses. The position of your Sound Blaster Wireless devices as well as signals from other wireless routers or Bluetooth equipment may affect the quality of the transmissions. Try the following: · In the Sound Blaster Wireless Control Panel, change the RF Channel from Auto to either Ch 1, 2 or 3. · Place your transmitter and receivers closer to each other. Use the extension cradle for more flexibility in placing your transmitter. Contact local agencies for recycling and disposal information. · Do not allow metal objects to touch the terminals of your battery. · If there is leakage, an offensive odor, discoloration or deformation during charging or use, remove the battery and do not use it again. Clean your hands well before touching food or sensitive areas, for example, your eyes. Wireless Device · Switch off the device where it is prohibited, or when its use may cause danger or interference such as inside an aircraft, hospitals, or near refuelling points. Declaration of Conformity 21 Declaration of Conformity According to the FCC96 208 and ET95-19 Manufacturer/Importer's Name: Creative Labs, Inc. Manufacturer/Importer's Address: 1901 McCarthy Boulevard Milpitas, CA. 95035 United States Tel: (408) 428-6600 declares under its sole responsibility that the product Trade Name: Creative Labs Model Numbers: SB1170 has been tested according to the FCC / CISPR22/97 requirement for Class B devices and found compliant with the following standards: EMI/EMC: ANSI C63. 4 2003, FCC Part 15 Subpart B & C Complies with Canadian ICES-003 Class B, RSS-GEN & RSS-210 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. Ce matériel est conforme à la section 15 des régles FCC. Son Fonctionnement est soumis aux deux conditions suivantes: (1) Le matériel ne peut étre source D'interférences et (2) Doit accepter toutes les interférences reques, Y compris celles pouvant provoquer un fonctionnement indésirable. Compliance Manager Creative Labs, Inc. March 18th, 2010 Regulatory Information 22 Regulatory Information Notice for the USA FCC Part 15: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] However, out of an abundance of caution, Creative has elected to place the Proposition 65 warning on its products. Déclaration de la Proposition 65 de la Californie AVERTISSEMENT: La manipulation de ce produit peut vous exposer à des produits chimiques qui sont reconnus par l'État de la Californie comme pouvant provoquer le cancer, des anomalies congénitales ou d'autres effets nuisibles à la reproduction. Veuillez vous laver les mains après l'avoir manipuler. Note explicative: La Proposition 65 (California Safe Drinking Water and Toxic Enforcement Act of 1986) de la Californie sur les matières dangereuses et l'eau potable exige un étiquetage spécial pour les produits contenant certains produits chimiques qui sont Regulatory Information 24 reconnus par l'État de la Californie comme pouvant provoquer le cancer, des anomalies congénitales ou d'autres effets nuisibles à la reproduction. [. . . ]