Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CREST AUDIO PRO 5200. We hope that this CREST AUDIO PRO 5200 user guide will be useful to you.
Lastmanuals help download the user guide CREST AUDIO PRO 5200.
Manual abstract: user guide CREST AUDIO PRO 5200DATASHEET
Detailed instructions for use are in the User's Guide.
[. . . ] Pro 5200/7200/8200/9200
Power Amplifiers
Pro 200TM
SERIES
(Pro 8200 shown)
Power Specifications
9200 8200 7200 5200
8 stereo* 1, 300 W 825 W 590 W 290 W
4 stereo* 2, 200 W 1, 450 W 1, 000 W 525 W
2 stereo* 3, 250 W 2, 250 W 1, 650 W 850 W
8 bridged** 4, 400 W 2, 900 W 2, 000 W 1, 050 W
4 bridged** 6, 500 W 4, 500 W 3, 300 W 1, 700 W
8, 4 Stereo and 8 Bridged Mono Power ratings @ 1 kHz, <. 05% THD+N both channels driven. 2 stereo and 4 Bridged Mono Power ratings @ 1kHz, <. [. . . ] (10. 9 kg)
Architects' & Engineers' Specifications:
The power amplifier shall consist of 2 channels. Each channel will delver a minimum of (290 / 590 / 825 / 1300) watts at 8 ohms, (525 / 1000 / 1450 / 2200) watts at 4 ohms, (850 / 1650 / 2250 / 3250) watts at 2 ohms, 20 Hz 20 kHz. In Bridged mono mode, it will deliver a minimum of (1050 / 2000 / 2900 / 4400) at 8 ohms, (1700 / 3300 / 4500 / 6500) at 4 ohms, 20Hz 20 kHz. The amplifier shall incorporate protection circuitry against output short circuits, DC voltage on outputs, thermal overload and load protection due to any form of amp failure. It will include impedance sensing circuitry, a RMS clip limiter and Autoramp signal control. The amplifier shall have a sensitivity of 1. 12 / 1. 58 / 1. 87 / 2. 35 volts (x40) at the input, which will deliver full rated output power in any output configuration. The hum and noise level shall be greater than (-110 dB / -110 dB / -110 dB / -113 dB) "A" weighted. The amplifier shall have a class (A / B, H, H, H) output stage with a switch power supply. The frequency response shall be greater than 10 Hz 100 kHz +0, -2 dB at1 watt at full rated output power @ 4 ohms . 05% THD. The amplifier will operate at either 120 VAC, 60 Hz (safe operating range 100-132 VAC) or at 230 VAC, 50 Hz (safe operating range 200-264), voltage selection determined at factory. Maximum current draw at 120 V shall be no greater then 30amps, both channels driven continuously into a 2 ohm load at 1/8 power. Front panel indicators shall include LED indicators for signal present, ACL (automatic clip limiting), Temp, and Active status. [. . . ] (OJ(L)37/38, 13. 02. 03 and defined in EN 50419: 2005 The bar is the symbol for marking of new waste and ver 1. 0 09/22/05 is applied only to equipment manufactured after 711 A Street, Meridian, MS 39301 USA · TEL: 866. 812. 7378 13 August 2005
Crest Audio Inc. · FAX: 601. 486. 1380 · www. crestaudio. com
® [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CREST AUDIO PRO 5200
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CREST AUDIO PRO 5200 will begin.
