User manual CRESTON CLSI-C6MRF INSTALLATION

[. . . ] 6418), for detailed configuration options. · · Cresnet network cable(s) (not supplied) Terminal block connector(s) (two supplied) Important Notes Read before installation. · · · Codes: Install in accordance with all local and national electrical codes. For supply connections, use wires rated for at least 75°C. [. . . ] If Cresnet cabling is part of the installation, attach the supplied terminal block connector to the Cresnet cable and plug into the LOCAL DEVICES port on the unit. Make certain that there is a minimum 63 mm (1/4-inch) separation between the Class 2 Cresnet wiring and the Class 1 AC wiring. Carefully tuck all wires into the wallbox and fasten the unit to the wallbox using the four 22 mm (7/8-inch) Phillips screws supplied. Reattach the control panel overlay to the front panel by inserting the four tabs into the slots provided, and install the hinged front cover assembly by lining it up at the top and pressing the bottom edge until it snaps into position. 8. Adding External Power Supplies Additional power supplies are required to support more than four keypads or shade controllers on the LOCAL DEVICES network. Also, each C2N-SDC-DC shade controller requires its own additional power supply. The diagram to the right illustrates a scenario where an external power supply is required to add a shade controller and other devices to a network that already contains four shade controllers. The actual quantity of external power supplies required depends on your system configuration. The illustration on the following page shows a variety of installation configurations. Adding External Power Supply Check Network Wiring In order to ensure optimum performance over the full range of your installation topology, use Crestron Certified Wire only. Failure to do so may incur additional charges if support is required to identify performance deficiencies because of using improper wire. CAUTION: Use only Crestron power supplies for Crestron equipment. Failure to do so could cause equipment damage or void the Crestron warranty. CAUTION: Provide sufficient power to the system. Insufficient power can lead to unpredictable results or damage to the equipment. Refer to the Supported Devices table on page 5. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (www. crestron. com/calculators). Installation Guide ­ DOC. 6417B iLuxTM Integrated Lighting Systems w/infiNETTM: CLSI-C6RF & CLSI-C6MRF · 3 iLuxTM Integrated Lighting Systems w/infiNETTM CLS-C6RF Installation Configurations 4 · iLuxTM Integrated Lighting Systems w/infiNETTM: CLSI-C6RF & CLSI-C6MRF Installation Guide ­ DOC. 6417B iLuxTM Integrated Lighting Systems w/infiNETTM Supported Devices The following table lists iLux-supported devices and their power requirements. Supported Devices NAME C2N-DB6 C2N-DB8 C2N-DB12 C2N-CBD/CBF C2NI-CB/ INETI-CB C2N-SDC C2N-SDC-DC DESCRIPTION 6-Button Keypad 8-Button Keypad 12-Button Keypad Cameo Keypad Cameo Keypad (International) Shade / Drape Controller Shade / Drape Controller (24VDC) Somfy Shade Controller 2-Button Keypad 4-Button Keypad 6-Button Keypad 8-Button Keypad 12-Button Keypad Sensor Integration Module CRESNET POWER FACTOR (W) 3 Watts 3 Watts 3 Watts 0. 5 Watts 0. 5 Watts 3 Watts Up to 32 Watts MAX. QTY 16 16 16 16 16 16 16 Power up and Testing The following illustration shows the front panel of the unit and the controls used during installation. Front Panel Controls and Indicators C2N-SSC-2 CNX-B2 CNX-B4 CNX-B6 CNX-B8 CNX-B12 GLS-SIM 1 Watt 3 Watts 3 Watts 3 Watts 3 Watts 3 Watts 1 Watt plus attached sensor wattage 1 Watt Partitions Occupancy sensing BMS integration 16 16 16 16 16 16 36 2 4 2 Verify the basic installation and wiring connections as follows: 1. Press the Lights button to enable manual light control, and press the right side and the left side of each of the function buttons to increase and decrease the lighting level of those loads. Verify that the intended loads and corresponding LED bargraphs respond appropriately. Press the OFF button to turn off all loads. The loads will ramp down to off while the two-digit display counts down to off (blank). [. . . ] * CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. Windows is a registered trademark of Microsoft Corporation. Windows 95/98/Me/XP/Vista/7 and Windows NT/2000 are trademarks of Microsoft Corporation. * Refer to the latest version of the Crestron CLSI-C6RF Integrated iLux Lighting System w/infiNET Operations Guide (Doc. 6418) for details on setting load types and low-end limits. Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling Crestron at 1-888-CRESTRON [1-888-273-7876]. [. . . ]