User manual CRESTON FT-PWR-D

[. . . ] Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. All brand names, product names and trademarks are the property of their respective owners. ©2010 Crestron Electronics, Inc. Crestron FT-PWR-D & FT-PWR-D-LG FlipTop Power Centers Contents FlipTop Power Centers, Dual AC Outlets: FT-PWR-D & FT-PWR-D-LG 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Place bushings on the cables you wish to install in the power center (eight bushings supplied). Use bushings appropriate for the diameter of each cable. Thread the cables through the cable support plate slots appropriate for the size of the cable and the bushing you attached in the previous step. Snap the bushings into the slots on the cable support plate. Feed all excess cable through the opening. Attach the cable support plate using the four #04-40 x 1/4" screws. If desired, any installed cables can be secured to the bottom bar with tie wraps (not supplied). 2. 6. 10 · FlipTop Power Centers: FT-PWR-D & FT-PWR-D-LG Operations & Installation Guide ­ DOC. 6640C Crestron FT-PWR-D & FT-PWR-D-LG Cable Support Plate Installation FlipTop Power Centers When selecting cables for installation in the FT-PWR-D/-LG, cable connector length and strain relief diameter are important considerations. · · If the connector is too long, it can interfere with cover operation. If the width of the cable strain relief is too similar to the bushing inside diameter, the bushing can trap the cable. NOTE: Do not use the cable support plate without the bushings. Example Cable End Must be wider than the inside diameter of the bushing. Position the FT-PWR-D/-LG in the mounting hole. 2. Operations & Installation Guide ­ DOC. 6640C FlipTop Power Centers: FT-PWR-D & FT-PWR-D-LG · 13 FlipTop Power Centers Mounting Bracket Screw Locations Crestron FT-PWR-D & FT-PWR-D-LG Screws (4) #06-32 X 3/16" (Pre-Installed) Screws (4) #06-32 X 3/16" (2007204) Surface Cutout 3. Thread a small portion of the #10-32 x 2" screws (2007293) into the mounting brackets (two screws per bracket). Refer to the illustration on the following page. Slide the mounting brackets over the #06-32 screws and tighten the #06-32 screws. 4. 14 · FlipTop Power Centers: FT-PWR-D & FT-PWR-D-LG Operations & Installation Guide ­ DOC. 6640C Crestron FT-PWR-D & FT-PWR-D-LG Mounting Bracket Installation FlipTop Power Centers 5. Turn the four #10-32 screws equally until they contact the underside of the mounting surface enough to secure the unit. DO NOT OVER-TIGHTEN. CAUTION: Do not over-tighten the #10-32 screws as this may damage the surface and/or the unit. FT-PWR-D (Mounting Brackets Installed) Operations & Installation Guide ­ DOC. 6640C FlipTop Power Centers: FT-PWR-D & FT-PWR-D-LG · 15 FlipTop Power Centers FT-PWR-D-LG (Mounting Brackets Installed) Crestron FT-PWR-D & FT-PWR-D-LG Hardware Hookup Hookup consists of simply plugging the line cord into an appropriate outlet. NOTE: The maximum continuous current from equipment under any external load conditions shall not exceed a current limit that is suitable for the minimum wire gauge used in interconnecting cables. The ratings on the connecting unit's supply input should be considered to prevent overloading the wiring. 16 · FlipTop Power Centers: FT-PWR-D & FT-PWR-D-LG Operations & Installation Guide ­ DOC. 6640C Crestron FT-PWR-D & FT-PWR-D-LG FlipTop Power Centers Operation The spring-loaded lid is opened by pressing briefly and releasing it. Cables are stored neatly beneath the lid when not in use to keep out debris and dust. The lid opens 135 degrees, allowing full access to cables and power inside. [. . . ] Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties. Trademark Information All brand names, product names and trademarks are the sole property of their respective owners. [. . . ]