User manual CRESTON GREEN LIGHT EXPRESS DIMMING PANEL INSTALLATION GUIDE

[. . . ] GREEN LIGHT® EXPRESS Dimming Panel Introduction CRESTRON GREEN LIGHT EXPRESS dimming panels come pre-configured with GLXX-2DIM8 dimming modules already installed. The cabinets only require installation and wiring of feed and load circuits. Application The following diagram shows CRESTRON GREEN LIGHT EXPRESS dimming panels in a lighting application that is controlled by an IPAC system. CRESTRON GREEN LIGHT EXPRESS Dimming Panels in a Typical Lighting Application C R E S N E T C O N T R O L C R E S N E T C R E S N E T O V E R R I D E Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888. CRESTRON Fax: 201. 767. 7576 www. crestron. com Installation Guide ­ DOC. 6889A (2025420) 05. 10 Specifications subject to change without notice. Dimming Panel CRESTRON GREEN LIGHT® EXPRESS Regulatory Compliance This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc. As of the date of manufacture, the Green Light Express Dimming Panel has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. [. . . ] System commissioning not complete. CORRECTIVE ACTION Use the provided Crestron power source. Use the Crestron Power Calculator to help calculate how much power is needed for the system. GLS-PLS-120/277 phase-loss sensor may not have been installed properly, or actual phase-loss has been detected). Unit cannot be taken out of Override mode Short (contact closure) exists between G and OVR terminals on any of the OVERRIDE terminals present at bottom of the cabinet. Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling Crestron at 1-888-CRESTRON [1-888-273-7876]. You can also log onto the online help section of the Crestron website (www. crestron. com/onlinehelp) to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. 18 · GREEN LIGHT® EXPRESS Dimming Panel Installation Guide ­ DOC. 6889A CRESTRON GREEN LIGHT® EXPRESS Dimming Panel Appendix A: Setting Module Net IDs The following procedure will normally be performed by an authorized Crestron representative as part of the System Commissioning phase. For system wiring and basic testing as described on pages 10 and 14, it is not necessary to perform this step. Only perform this step if instructed by an authorized Crestron representative, or when replacing modules on a system that have already been commissioned (in the latter case the Net ID should be set to match the Net ID of the module being replaced). The Net ID of each module in the cabinet can be changed from the front panel of each module. The Net IDs of each module in the system must be unique. To set the Net ID using the front panel: 1. Press the recessed SETUP button to enter the Setup mode. As shown in the following diagram, press the left button under the NET ID display to change the left digit of the Net ID or press the right button under the NET ID display to change the right digit of the Net ID number. Changing the Net ID LABEL FOR NET ID LEFT DIGIT RIGHT DIGIT CHANGES LEFT DIGIT CHANGES RIGHT DIGIT SETUP BUTTON & LED 3. When the desired Net ID is displayed, press the SETUP button to exit the Setup mode. If the SETUP button is not pressed, the Setup mode will time out after one minute activity and the Net ID will revert back to its original value. Installation Guide ­ DOC. 6889A GREEN LIGHT® EXPRESS Dimming Panel · 19 Dimming Panel CRESTRON GREEN LIGHT® EXPRESS Appendix B: Specifications Specifications for the GLXX-2DIM8 modules are listed in the following table. GLXX-2DIM8 Module Specifications SPECIFICATION Input Voltage Supported Load Types Maximum Load Lighting Motor Environmental Temperature Humidity Heat Dissipation 100 ­ 277 VAC 50/60 Hz DETAILS Incandescent, HID, magnetic low voltage (MLV), electronic low voltage* (ELV), neon/cold cathode, and fluorescent ballasts, motor 16 A per output (16A max total for group 1-4 and 16A max total for group 5-8) 1 hp @ 120V 2 hp @ 230V/277V 32º to 104º F (0º to 40º C) 10% to 90% RH (non-condensing) 154 BTU/HR Cresnet Power 5W Usage * Forward phase or leading edge compatible transformers only. 20 · GREEN LIGHT® EXPRESS Dimming Panel Installation Guide ­ DOC. 6889A CRESTRON GREEN LIGHT® EXPRESS Dimming Panel Appendix C: Network Wiring Check Network Wiring Use the Right Wire In order to ensure optimum performance over the full range of your installation topology, Crestron Certified Wire and only Crestron Certified Wire may be used. Failure to do so may incur additional charges if support is required to identify performance deficiencies because of using improper wire. Calculate Power CAUTION: Use only Crestron power supplies for Crestron equipment. Failure to do so could cause equipment damage or void the Crestron warranty. CAUTION: Provide sufficient power to the system. Insufficient power can lead to unpredictable results or damage to the equipment. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (www. crestron. com/calculators). When calculating the length of wire for a particular Cresnet run, the wire gauge and the Cresnet power usage of each network unit to be connected must be taken into consideration. [. . . ] Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number and return address. Products may be returned for credit, exchange or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. [. . . ]