User manual CRESTON WMKM-9L INSTALLATION

[. . . ] Crestron MMK-9L & WMKM-9L Mud Mount Kits Installation Guide Crestron MMK-9L & WMKM-9L Mud Mount Kits This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Contents Mud Mount Kits: MMK-9L & WMKM-9L 1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Supplied Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Slide them on enough to keep the adjustment plate and mounting plate as one adjustment/mounting plate assembly. Use the second adjustment plate and repeat steps 1 and 2 using the lower two PMK-9L (or BB-9L) pins. NOTE: When installing into the PMK-9L, verify the 18 AWG bus wire securing the cables for the touchpanel remains attached. 3. 4. Insert the symmetrical mud ring plate into the opening, as shown in the following illustration. Installation Guide ­ DOC. 7033A Mud Mount Kits: MMK-9L & WMKM-9L · 5 Crestron MMK-9L & WMKM-9L Insert and Secure Mud Ring Plate into PMK-9L (or BB-9L) Mud Mount Kits PMK-9L Drywall Holes for Drywall Screws (not included) Screw length should not exceed drywall thickness by more than 1/2" (13 mm) Mud Ring (2028252) 5. When the mud ring is in position, bend the top two flanges of the ring upward and the bottom two flanges downward. · · If mounting into the PMK-9L, bend the flanges approximately 90 degrees. If mounting into the BB-9L, bend the flanges back as far as they can go. 6. Use four standard drywall screws (length should not exceed drywall thickness by more than 1/2" (13 mm)) to secure the mud ring plate to the rest of the assembly. The screws pass through the clearance holes in the PMK-9L (or BB-9L) and are secured in the extruded holes of the adjustment plates. Doing so can rip the mud ring plate. 7. 8. 9. Use a #2 Phillips screwdriver and tighten the drywall screws by hand so they slightly dimple into the holes in the mud ring plate. Apply joint compound as needed to finish the cutout. Avoid covering the four tapped mounting holes. 10. Run the necessary cables for the touchpanel and secure them behind the drywall. When the joint compound is dry, the TPMC-9L can be installed using the four tapped holes in the PMK-9L or BB-9L. Refer to the latest revision of the TPMC-9L Operations & Installation Guide (Doc. Refer also to the following comprehensive illustration. 6 · Mud Mount Kits: MMK-9L & WMKM-9L Installation Guide ­ DOC. 7033A Crestron MMK-9L & WMKM-9L Touchpanel Mounting Using MMK-9L (Exploded View) Mud Mount Kits Drywall Mud Ring (2028252) PMK-9L (not included) TPMC-9L TPMC-9L Mounting Screws (4) #04-40 x 1 1/2" Drywall Screws WMKM-9L Procedure This section provides the necessary steps for assembly and installation of the WMKM-9L into a wall, lectern, podium or furniture-like cabinet. Review the procedure and complete the steps in the order provided. The only tools or materials required and not supplied are a drywall saw or equivalent, a level, four application appropriate screws, #2 Phillips screwdriver and tools/material to apply drywall joint compound. CAUTION: Allow an air gap of at least 12 inches (305 mm) in the wall cavity above and below the touchpanel for heat dissipation. NOTE: The WMKM-9L has been optimized for mounting in 5/8" (15 mm) drywall. You may use 1/2" ­ 1" (13 mm ­ 25 mm) without issue. Thinner or thicker drywall will cause issues with the installation. [. . . ] or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. [. . . ]