User manual CRESTRON AADS AADS-XM

[. . . ] Crestron AdagioTM AADS Adagio Audio Distribution System Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Important Safety Instructions · · · · · · · · Read these instructions. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] · · Access the Room Setup mode as described on page 31. Press down on the selection control until Start Volume is displayed and press SELECT to open the Startup Volume control. The current startup volume setting is displayed. 32 · Audio Distribution System: Adagio AADS Operations Guide ­ DOC. 6458 Crestron AdagioTM AADS Audio Distribution System Startup Volume Control SOURCE ROOM PRESET MENU BKLT Room 6 Start Volume 50% SCHED DISPLAY MORE · Adjust the maximum volume with the selection control. Press up to raise the maximum volume or press down to lower the maximum volume. The maximum startup volume setting is 50%. Press SELECT to store the startup volume setting and to return to the Room Setup menu. · Set Mono or Stereo Mode The audio sent to the speakers in each room can be set for either stereo or mono. When set to stereo, the audio signal is separated into left and right channels for distribution to left and right speakers. When set to mono, the audio signal is combined into one signal for use in larger rooms where stereo separation is not practical. The mono/stereo settings of each room can be adjusted independently. · · Access the Room Setup mode as described on page 31. Press down on the selection control until Stereo/Mono is displayed and press SELECT to open the Stereo/Mono control. The selected mode is displayed on the LCD. Stereo/Mono Control SOURCE ROOM PRESET MENU BKLT Room 6 Stereo SCHED DISPLAY MORE · · · To select stereo, press the selection control down to display Stereo and press SELECT. To select mono, press the selection control up to display Mono and press SELECT. To cancel and return to the Room Setup menu, press the MENU button. Configure Presets Presets can be created to group speakers in adjacent rooms with a specified source, or switch into a whole-house "party" mode, by letting the user link a source with any number of rooms. Changing the source in any one room changes the source in all of the rooms in the preset. Edit a Preset To edit a preset: · Press and hold the PRESET button for approximately five seconds to view the Edit Presets control shown in the following diagram. Operations Guide ­ DOC. 6458 Audio Distribution System: Adagio AADS · 33 Audio Distribution System Edit Presets Control SOURCE ROOM PRESET MENU Crestron AdagioTM AADS BKLT Edit Presets 1: Party SCHED DISPLAY MORE · · To configure a preset, press up or down on the selection control to display the preset to be configured and press SELECT. To add rooms to the preset, press the corresponding room buttons on the AADS or AAE (if connected). The room button's LED will turn on. Press again to remove the room from the preset group. The room button's LED will turn off. [. . . ] CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials and workmanship under normal use for a period of three (3) years from the date of purchase from CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and overlay components are covered for 90 days; batteries and incandescent lamps are not covered. [. . . ]