User manual CRESTRON BB-1550CW

[. . . ] If installing the back box to the left-side of a stud, reverse the mounting bracket and the mounting support bracket but maintain the orientation of the back box enclosure with the manual unlatching notch at the top. Locate the position and height that the back box (and touchpanel) will be installed. 2 · Wall Mount Back Box for STX-1550CW: BB-1550CW Installation Guide - DOC. 5848 Crestron BB-1550CW 2. Wall Mount Back Box for STX-1550CW Refer to the diagram below. Position the mounting bracket at the edge of the stud. [. . . ] Make sure that the area is clear of studs, wires, or other obstructions within the installation area. Installation Guide - DOC. 5848 Wall Mount Back Box for STX-1550CW: BB-1550CW · 5 Wall Mount Back Box for STX-1550CW Crestron BB-1550CW 2. 3. Using a stud finder (or equivalent), locate the right-edge of a stud within the installation area. Align the left dashed, vertical line (labeled STUD EDGE) of the supplied template with the right-edge of the stud. Refer to "Appendix: Cutout Detail of Supplied Template" on page 10 for an illustrative reference. Using masking tape, fasten the supplied template to the wall; verify that the cutout is level. Using a preferred method, transfer the cutout area of the template to the gypsum board at the location of the back box. Using a gypsum board saw (or equivalent), cut the rectangular area through the wall. Remove the template and cutout area. 4. 7. NOTE: To prevent the mounting bracket from falling into the wall cavity, it is recommended to tie a safety string to the bracket when performing the next step. Through the cut-out area, position the mounting bracket at the edge of the stud (flush with the back-side of the gypsum board) and vertically centered in the cut-out area. Through the mounting bracket slots closest to the center of the bracket and using a #2 Phillips screwdriver, secure the bracket to the stud using four wood screws (not supplied). Secure Mounting Bracket to Stud 6 · Wall Mount Back Box for STX-1550CW: BB-1550CW Installation Guide - DOC. 5848 Crestron BB-1550CW 9. Wall Mount Back Box for STX-1550CW Orient the back box enclosure as shown below (notch for manual unlatching upwards) and remove an appropriate knockout for the Cresnet wiring. Back Box Enclosure Orientation NOTCH FOR MANUAL UNLATCH TAB ACCESS REMOVED KNOCKOUT 10. As shown below, loosely install four pan head screws with washers through the inside of the enclosure into the support bracket holes. Tighten screws only finger-tight so that final adjustments may be made during step 14 of this procedure. Loosely Install Support Bracket 11. Position the back box enclosure near the cut-out area and feed the Cresnet wiring through the enclosure knockout. Installation Guide - DOC. 5848 Wall Mount Back Box for STX-1550CW: BB-1550CW · 7 Wall Mount Back Box for STX-1550CW Crestron BB-1550CW 12. Making sure that the support bracket is behind the gypsum board, position the enclosure into the cutout area. As shown below, loosely install four pan head screws with washers through the inside of the enclosure into the mounting bracket holes. Tighten screws only finger-tight so that final adjustments may be made during the next step of this procedure. Loosely Secure Enclosure to Mounting Bracket 14. As shown below, use a ruler to adjust the back box to approximately 1/16-inch (0. 15 cm) inward of the face of the gypsum board to accommodate the distance between the back box and the front panel. Using a #2 Phillips screwdriver, tighten the four pair of bracket screws finger-tight plus an additional 1/8-turn. Adjust Back Box Clearance and Tighten Bracket Screws BACK BOX CLEARANCE (ALL SIDES) 8 · Wall Mount Back Box for STX-1550CW: BB-1550CW Installation Guide - DOC. [. . . ] To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]