User manual CRESTRON BB-1600

[. . . ] 11 CRESTRON Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5835A Contents · i Crestron BB-1600 Back Box Back Box: BB-1600 Description The back box, BB-1600, is the optional mounting hardware that secures a Crestron Series 1600 Lectern/Wall Mount Touchpanel to a wall or other suitable mounting surface. Supplied Components DESCRIPTION Metal Electrical Box with 4 knockouts Metal Mounting Bracket Metal Mounting Plate Screw, 6-32 x 1"L, pan, phillips, black Screw, 6-32 x 3/8"L, socket hex Template PART NUMBER QUANTITY AY17434-1 MTBK02542-1 MTPL02541-1 SR06-32-1R000-3 SR06-32-0R3750-3 OV40047-1 1 2 2 4 4 1 Three views with dimensions for the metal pieces of the BB-1600 are shown below and on the next page. BB-1600 Physical Views and Dimensions (Top View) Installation Guide - DOC. [. . . ] Tighten four screws installed in steps 10 and 12 with a Phillips screwdriver. Verify that the rim of the back box is recessed approximately 1/8" from the mounting surface and use fingers to tighten four socket hex head screws. Using a socket screwdriver, tighten each screw an additional 1/8-turn. If touchpanel is available, secure touchpanel to BB-1600 using four pan head screws, supplied with the touchpanel. 9. 14. 15. Post-Construction Method The only tools required are a gypsum board saw (or equivalent), a socket screwdriver (length should not exceed 4. 5"), a #2 Phillips tip screwdriver, a drill, a 5/16" drill bit, and a #20 drill bit. Complete the following installation procedure in the order provided. Locate an area on the wall or other suitable mounting surface that is clear of studs, wires, and other obstructions. Make a small hole near the middle of the designated site; verify location is suitable. Fasten cutout template (40047, supplied) to mounting surface; verify that the template is level. Cut out and remove the traced shape of mounting surface. Refer to "Cutout Detail of Supplied Template" on page 10 for an illustrative reference. Installation Guide - DOC. 5835A Back Box: BB-1600 · 5 Back Box 6. Crestron BB-1600 Drill eight holes marked "A" with #20 drill. Refer to "Cutout Detail of Supplied Template" on page 10 for an illustrative reference. Slide one metal mounting bracket through the opening and position it inside along the top horizontal edge. Position one metal mounting plate along the top horizontal edge so that it covers the two center holes marked "A". Use two pan head screws, supplied, to secure the bracket and plate to the mounting surface. Tighten by hand; do not fully tighten screws. Securing Bracket/Plate Assembly to Top and Bottom Edges of Opening 7. 9. METAL MOUNTING BRACKET METAL MOUNTING PLATE TWO PAN HEAD SCREWS (MOUNTS BRACKET AND PLATE IN TWO CENTER TAPPED HOLES) DRYWALL 10. Repeat steps 7 through 9 for the bottom horizontal edge of the opening. Remove necessary knockout(s) from metal electrical box. Pull Cresnet wire through open punch in metal electrical box. 6 · Back Box: BB-1600 Installation Guide - DOC. [. . . ] Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. [. . . ]