User manual CRESTRON BB-1700CW

[. . . ] 11 Merchandise Returns / Repair Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 CRESTRON Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6105 Contents · i Crestron BB-1700CW Wall Mount Back Box for STX-1700CW Wall Mount Back Box for STX-1700CW: BB-1700CW Introduction The BB-1700CW back box is wall-mounted hardware that is used to secure the DA-1700CW docking assembly (sold separately). When used with the BB-1700CW, the docking assembly provides operating power, hard-wire communications with a standard Crestron remote control system (herein referred to as the Cresnet system), and recharges the Crestron High Performance Rechargeable Power Pack (ST-BTPN) of a Crestron SmarTouch STX-1700CW compact color touchpanel. Supplied Components DESCRIPTION Metal, Enclosure Metal, Bracket, Mounting Metal, Bracket, Mounting Support Screw, 6-32, ¼ "L Steel Washer, Flat, Steel, B Regular Overlay, Template, Wall Cutout PART NUMBERS MTEN02571-1 MTBK02577-1 MTBK02578-1 SR06-32-0R2500-2 WA06FL-2 OV40053-1 QUANTITY 1 1 1 8 8 1 A diagram of the two installation brackets is shown below and three views of the back box enclosure are shown on the next page. Installation Brackets MOUNTING BRACKET SUPPORT BRACKET Installation Guide ­ DOC. [. . . ] NOTE: This procedure installs the left-side of the back box to the right-side of a framing stud. If installing the back box to the left-side of a stud, reverse the mounting bracket and the mounting support bracket but maintain the orientation of the back box enclosure with the manual unlatching notch at the top. Locate an area on the wall that the back box (and touchpanel) will be installed. Make sure that the area is clear of studs, wires, or other obstructions within the installation area. Installation Guide ­ DOC. 6105 Wall Mount Back Box for STX-1700CW: BB-1700CW · 5 Wall Mount Back Box for STX-1700CW Crestron BB-1700CW 2. 3. Using a stud finder (or equivalent), locate the right-edge of a stud within the installation area. Align the left dashed, vertical line (labeled STUD EDGE) of the supplied template with the right-edge of the stud. Refer to "Appendix: Cutout Detail of Supplied Template" on page 10 for an illustrative reference. Using masking tape, fasten the supplied template to the wall; verify that the cutout is level. Using a preferred method, transfer the cutout area of the template to the gypsum board at the location of the back box. Using a gypsum board saw (or equivalent), cut the rectangular area through the wall. Remove the template and cutout area. 4. 7. NOTE: To prevent the mounting bracket from falling into the wall cavity, it is recommended to tie a safety string to the bracket when performing the next step. Through the cut out area, position the mounting bracket at the edge of the stud (flush with the back-side of the gypsum board) and vertically centered in the cut-out area. Through the mounting bracket slots closest to the center of the bracket and using a #2 Phillips screwdriver, secure the bracket to the stud using four screws (not supplied). Secure Mounting Bracket to Stud 6 · Wall Mount Back Box for STX-1700CW: BB-1700CW Installation Guide ­ DOC. 6105 Crestron BB-1700CW 9. Wall Mount Back Box for STX-1700CW Orient the back box enclosure as shown below (notch for manual unlatching upwards) and remove an appropriate knockout for the Cresnet wiring. Back Box Enclosure Orientation NOTCH FOR MANUAL UNLATCH TAB ACCESS REMOVED KNOCKOUT 10. As shown below, loosely install four pan head screws with washers through the inside of the enclosure into the support bracket holes. Tighten screws only finger-tight so that final adjustments may be made during step 14 of this procedure. Loosely Install Support Bracket 11. Position the back box enclosure near the cut-out area and feed the Cresnet wiring through the enclosure knockout. Installation Guide ­ DOC. 6105 Wall Mount Back Box for STX-1700CW: BB-1700CW · 7 Wall Mount Back Box for STX-1700CW Crestron BB-1700CW 12. Making sure that the support bracket is behind the gypsum board, position the enclosure into the cutout area. As shown below, loosely install four pan head screws with washers through the inside of the enclosure into the mounting bracket holes. [. . . ] Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supercedes all previous warranties. Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. [. . . ]