User manual CRESTRON CHV-TSTAT CHV-THSTAT FIRMWARE BETWEEN 1.1-2.0

[. . . ] Crestron CHV-TSTAT & CHV-THSTAT Thermostats Operations and Installation Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2003 Crestron Electronics, Inc. Crestron CHV-TSTAT and CHV-THSTAT Thermostats Contents Quick Installation Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Thermostats: CHV-TSTAT and CHV-THSTAT 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functions and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The CHV-THSTAT also displays Relative Humidity and Humidifier Mode. Press the up arrow button to increase the set point temperature. Press the down arrow button to decrease the set point temperature. NOTE: If you selected Yes in setup screen #6 for "Dual Setpoint Auto", pressing MODE toggles between the Heat and Cool setpoints. This screen also indicates the system currently running: H1 ­ Heat System or Stage 1 Heat System H2 ­ Stage 2 Heat System AX ­ Auxiliary Heating System C1 ­ Cooling System or Stage 1 Cooling System C2 ­ Stage 2 Cooling System MODE MODE Button It may also be necessary to access the following series of screens. Pressing the MODE button allows the user to access the following screens: 1. Global Update System Mode Screen MODE 1. SYSTEM MODE The "System Mode" screen appears when the MODE button is initially pressed. Use the up and down arrow buttons to select HEAT, COOL, AUTO, OFF or AUX Heat Only. NOTE: The AUTO selection allows the system to switch between Heat and Cool automatically as needed to maintain the temperature. NOTE: The AUX HEAT ONLY is for the backup heating system on Heat Pump systems only. Allows the backup system to operate without operating the heat pump. System Mode HEAT COOL AUTO OFF AUX HEAT ONLY VIEW Fan Mode Screen MODE 2. FAN MODE Pressing the MODE button again displays the "Fan Mode" screen. Use the up and downarrow buttons to select AUTO or ON. NOTE: In AUTO, the fan runs only when the system calls for heat or cool. In ON, the fan runs continuously. Thermostats: CHV-TSTAT and CHV-THSTAT · 21 Fan Mode AUTO ON VIEW Operations and Installation Guide ­ DOC. 8163A Thermostats Crestron CHV-TSTAT and CHV-THSTAT Humidifier Screen MODE 3. Humidifier (CHV-THSTAT ONLY) Pressing the MODE button displays the "Humidifier" screen. Use the up and down arrow buttons to select ENABLED or DISABLED. Humidifier ENABLED DISABLED VIEW Crestron System Screen MODE 4. CRESTRON SYSTEM Pressing the MODE button again displays the Crestron System screen. Use the up and downarrow buttons to select ONLINE or HOLD. ONLINE ­ Data flows both ways, to and from the thermostat, enabling adjustment from a remote location. [. . . ] Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. [. . . ]