User manual CRESTRON CLT-2IND CLX-2IND CLT-4IND CLX-4IND

[. . . ] The relative humidity must be 10% to 90% (noncondensing). Terminal blocks are installed along the left side of singlewide enclosures and along the outside edges (left and right sides) of double-wide enclosures. Modules are installed along the right side of single-wide enclosures and side-by-side in the center of double-wide enclosures. [. . . ] Wires should be stripped to ½ inch. Test the circuit for electrical faults by turning on the circuit breaker and checking that the breaker does not trip and that the proper lighting loads are energized. FROM DIMMER TO LOAD FROM DIMMER TO LOAD 3. Wiring CLX-2IND Terminal Block to the Feed and Load(s) for Right Side of Double-Wide Enclosure TO LOAD FROM DIMMER TO LOAD FROM DIMMER 2 · Terminal Block & Module: CLT- & CLX-2IND/4IND Installation Guide ­ DOC. 6315 Crestron CLT- & CLX-2IND/4IND Wiring CLX-4IND Terminal Block to the Feed and Load(s) for Single-Wide Enclosure and Left Side of Double-Wide Enclosure Terminal Block & Module Module Installation NOTE: Modules are to be installed after enclosure has been completely wired. Refer to the terminal block installation procedure on page 2 for details. Use the four supplied self-tapping screws (8B x ¼ length) to secure the module to the enclosure. As shown in the following wiring diagrams, connect the wires from the module to the terminal block. Wires are pre-stripped to ½ inch. Tighten to 9 in-lbs. FROM DIMMER TO LOAD FROM DIMMER TO LOAD FROM DIMMER TO LOAD FROM DIMMER TO LOAD NOTE: Each inductor should be wired with one wire connected to an input and the other wire connected to the corresponding output. Turn off the circuit breaker and remove the bypass jumpers on the terminal block. Refer to following diagrams for a close-up of the jumpers. Wiring Diagram of the Terminal Block to the Inductor Module in a Single-wide Enclosure or the Left Side of a Double-wide Enclosure (CLT/CLX-2IND shown) Wiring CLX-4IND Terminal Block to the Feed and Load(s) for Right Side of Double-Wide Enclosure TO LOAD FROM DIMMER TO LOAD FROM DIMMER TO LOAD FROM DIMMER TO LOAD FROM DIMMER JUMPERS REMOVED Installation Guide ­ DOC. 6315 Terminal Block & Module: CLT- & CLX-2IND/4IND · 3 Terminal Block & Module Wiring Diagram of the Terminal Block to the Inductor Module, in the Right Side of a Double-wide Enclosure (CLT/CLX-4IND shown) Crestron CLT- & CLX-2IND/4IND Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. [. . . ] CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. [. . . ]