Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CRESTRON CNWMBG2-34A. We hope that this CRESTRON CNWMBG2-34A user guide will be useful to you.
Lastmanuals help download the user guide CRESTRON CNWMBG2-34A.
Detailed instructions for use are in the User's Guide.
[. . . ] CRESTRON CNWMBG2-34A
4. 63 in 11. 76 cm
Wall-Mount Wired Panel
1
2
3
4
5
6
7
8
9
10
BAR 1
100 80 60 40
BAR 2
11
12
13
14
15
16
17
18
19
20
20 0
4. 63 in 11. 76 cm
UP1
UP2
21
22
23
24
25
26
27
28
29
30
DOWN1
DOWN2
CRESTRON
Panel installs in 4-gang electrical box (1. 60 in (4. 06 cm) minimum depth).
SYNTAX:
NET. ID <10 to FE>: CNWP i1, o1 = <signal name> i2 = <signal name> o2 = <signal name> "= " " "= " " i30 = <signal name> o30 = <signal name> BAR1 = <signal name> UP1 = <signal name> DOWN1 = <signal name> BAR2 = <signal name> UP2 = <signal name> DOWN2 = <signal name> \ button and LED combined \ independent button \ independent LED
\ left bargraph \ left volume up button \ left volume down button \ right bargraph \ right volume up button \ right volume down button
DESCRIPTION:
The CNWMBG2-34A wired panel interfaces to a CRESNET II control system over the CRESNET II network. [. . . ] The ID CODE of the panel should be set to match the ID CODE specified in the NET. ID statement of the CRESNET II SIMPL-C program referencing the panel (refer to syntax section). To set an ID CODE, remove the panel from the electrical box and disconnect power. Accessible through the back plate are two miniature circuit-mounted rotary switches, identified as H and L. These 16position hexadecimal switches can be set to 0 through F. Using a small screwdriver, rotate the arrow in the center of the switch marked H to point to the first (or most-significant) digit or letter of the specified ID CODE. Set the switch marked L to the second (least-significant) digit or letter of the specified ID CODE. The 4-pin connector marked NET should be wired to the CRESNET II network. Network termination points are available at the control system power supply. [. . . ] CRESNET II Operating System SR30160. OPS or later.
FURTHER INQUIRIES:
If after reviewing this information you still have additional questions, please contact a CRESTRON technical support representative by dialing (888) CRESTRON [(888) 273-7876] or (201) 894-0660.
REMOTE
CONTROL
SYSTEMS
2
Specifications subject to change without notice.
DOC. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CRESTRON CNWMBG2-34A
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CRESTRON CNWMBG2-34A will begin.
