User manual CRESTRON CNX-ASBK

[. . . ] The Net ID of CNX-PAD8s is factory set to 44. The Net IDs of each of the daisy-chained CNX-PAD8s must be unique and changed from a PC via VisionToolsTM Pro-e (VT Pro-e) or SIMPL Windows. The method for changing the unit's Net ID is identical regardless of the software chosen. Verify that the control system software is running and complete the following steps to change the Net ID: 1. [. . . ] From the rear of the CNX-PAD8, remove the 10 back panel cover plate mounting screws and remove the cover plate. Back Panel Cover Plate Mounting Screws 10 COVER PLATE MOUNTING SCREWS G 24 Y Z G CRESNET 24VDC 1A 1-2 3-4 5-6 7-8 SOURCES 1 2 3 4 5 6 7 8 ROOMS 1 2 3 4 5 6 7 8 LEFT LEFT RIGHT RIGHT CRESTRON ELECTRONICS INC. Making sure that the rear of the PCB assembly faces the rear of the CNX-PAD8, insert the PCB into the position that was occupied by the back panel cover plate as shown after this step. Install the PCB with the 10 cover plate screws that were removed. 4 · Audio Switcher Bussing Kit: CNX-ASBK Operations & Installation Guide - DOC. 8143 Crestron CNX-ASBK Install the PCB Assembly Audio Switcher Bussing Kit 10 COVER PLATE SCREWS NOTE: DO NOT twist the cables during installation. The cables are custom designed and will fit perfectly. If the cable does not fit correctly, switch the cable ends from the PCB to the CNX-PAD8 processor PCB. Hold one end of the PCB to PCB cable (2-inch, 4-pin) toward the front of the CNX-PAD8. Carefully align and insert the other connector onto the connector on CNX-PAD8 processor PCB. Curl the cable directly above and insert the other connector onto the pins of the PCB as shown. Install the PCB to PCB Cables Operations & Installation Guide - DOC. 8143 Audio Switcher Bussing Kit: CNX-ASBK · 5 Audio Switcher Bussing Kit Crestron CNX-ASBK 14. Repeat the previous two steps for all of the remaining PCB to PCB cables. Install the rack mounting ears and then the remaining cover screws to 11-inch/pounds. Install the CNX-PAD8 Cover IF NOT RACK MOUNTED, INSTALL THESE (3) SIDE SCREWS ALSO INSTALL THREE (3) SIDE SCREWS INSTALL FOUR (4) TOP SCREWS INSTALL THREE (3) SIDE SCREWS IF NOT RACK MOUNTED, INSTALL THESE (3) SIDE SCREWS ALSO 16. If this procedure has been performed on only one CNX-PAD8, repeat this procedure from step 7 for all of the CNX-PAD8s to be daisychained. If the back panels of the CNX-PAD8s will be accessible when mounted in the rack, install the CNX-PAD8s. If the back panels will NOT be accessible, hookup all cables before installing into rack. NOTE: DO NOT twist the cables during installation. The cables are custom designed and will fit perfectly. If the cable does not fit correctly, switch the cable ends from one CNX-PAD8 to another. Note the position of the connector keys and install the bussing cables (6-inch, 12-conductor) from CNX-PAD8 to CNX-PAD8. Shown below are the bussing cables for audio sources 1 ­ 2. Connect the cables as required per custom installation. Install the Bussing Cables 12-PIN, 6-INCH CABLE TO CNX-PAD8 ABOVE, IF APPLICABLE G 24 Y Z G CRESNET 24VDC 1A 1-2 3-4 5-6 7-8 SOURCES 1 2 3 4 5 6 7 8 ROOMS 1 2 3 4 5 6 7 8 LEFT LEFT RIGHT RIGHT CRESTRON ELEC S INC. 07647 12-PIN, 6-INCH CABLE TO CNX-PAD8 BELOW, IF APPLICABLE NOTE POSITION OF CONNECTOR KEY 6 · Audio Switcher Bussing Kit: CNX-ASBK Operations & Installation Guide - DOC. [. . . ] Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supercedes all previous warranties. Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. [. . . ]