User manual CRESTRON IO 1700C-BTNB-BEZELS 1700C-BTNS-BEZELS

[. . . ] 6321A Button Bezel Kits: 1700C-BTNS/BTNB-BEZELS · 1 Button Bezel Kits Crestron 1700C-BTNS/BTNB-BEZELS If your 1700 Series touchpanel has blank pushbuttons and you find that engraved pushbuttons are required, purchase the 1700C-BTNB (black) or the 1700C-BTNS (silver) Replacement Button pack. Engraving is included in the purchase of these items. Contact Crestron customer support for more information. NOTE: A user may not want the LCD screen to come on after a pushbutton is pressed when the unit is off. [. . . ] Pushbuttons marked 1 ­ 5 should be installed to the left of the touchpanel screen while pushbuttons marked 6 ­ 10 should be positioned to the right of the screen. (Each button's marking includes `TOP' to ensure proper orientation. ) CAUTION: DO NOT cut or separate individual pushbuttons from the left and right pushbutton assemblies. Doing so will impair their use. Operations & Installation Guide - DOC. 6321A Button Bezel Kits: 1700C-BTNS/BTNB-BEZELS · 3 Button Bezel Kits Crestron 1700C-BTNS/BTNB-BEZELS NOTE: The pushbuttons fit snugly on the membrane switch actuators. Pushbuttons (right, 6 ­ 10) and Membrane Switch Actuator Pushbuttons Membrane Switch Actuators 5. Position the appropriate pushbuttons/membrane switch actuator assemblies on the sides of the display. Refer to the illustrations on the next page. Edge alignment ensures that the openings in the bezel will properly fit over the pushbuttons when the bezel is attached in step 6. Position the new bezel (with pushbutton cutouts) over the exposed touchpanel. It may be necessary to lightly rock the bezel so that the buttons align with the holes in the bezel. Hold the bezel to the touchpanel base and carefully rotate the entire panel onto its face once more. Reinstall the four screws to secure the bezel to the base. Tighten the screws, being careful not to strip the threads. Re-connect power and verify that the pushbuttons function properly. 4 · Button Bezel Kits: 1700C-BTNS/BTNB-BEZELS Operations & Installation Guide - DOC. 6321A Crestron 1700C-BTNS/BTNB-BEZELS Exploded View of Button Bezel Kit Bezel Button Bezel Kits Align Membrane Switch Actuator Edge & PCB Edge (Refer to Image Below for Detail) Pushbuttons (1 - 5) & Membrane Switch Actuator PCB Surface Pushbuttons (6 - 10) & Membrane Switch Actuator Detail of Edge Alignment Align Edge Operations & Installation Guide - DOC. 6321A Button Bezel Kits: 1700C-BTNS/BTNB-BEZELS · 5 Button Bezel Kits Crestron 1700C-BTNS/BTNB-BEZELS Problem Solving Troubleshooting If the touchpanel operation is otherwise normal, and one or more pushbuttons do not function as expected, there are two possible causes. If the touchpanel is an RF transceiver (all but the TPS-1700), it is out of range. The solution is to bring the unit back into range. Refer to the "Out of Range Feature" section in the Operations Guide of the respective touchpanel for more information. A wrong VT Pro-e project is uploaded to the touchpanel, and/or a wrong SIMPL Windows program is loaded to the control system. The solution is to upload the correct SIMPL Windows or VT Pro-e program. Refer to the respective help files for more information. Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. [. . . ] CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. Furthermore, this warranty does not cover any product that has had the serial number altered, defaced, or removed. This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages inclusive) arising from the sale or use of this equipment. [. . . ]