User manual CRESTRON IO IM-WCVP

[. . . ] Control and power signals are also contained on the same wire, eliminating the need for separate control or power cables. * For iMedia use CresCAT-IM cable, or quality CAT5e/CAT6 cable having a maximum delay skew of 15ns per 100m. 2-Piece Wall Plate Multimedia Interface The IM-WCCV-S is an iMedia (IM) transmitter featuring separate wall plates for interface and control. The interface panel (IM-WCVI) is designed to install in a standard 2-gang electrical box, providing video, RGB, and stereo audio inputs for connection to the output of a computer or AV source. The control panel (IM-WCVP) is a separate 1-gang wall plate, which may be installed up to 40 feet from the interface panel. Installing wiring for the IM-WCCV-S is extremely simple using CRESCAT-IM cable. [. . . ] Contact with thermal insulating materials should be avoided on all sides of the unit. Make the necessary connections as called out in the illustration that follows this paragraph. Turn on the system only after all connections have been made. Hardware Connections for the IM-WCVP Connect the Device TO IM-WCVI: CRESCAT-IM CONNECTION TO IM-WCVI GROUND REAR NOTE: For optimum performance, Crestron strongly recommends using CRESCAT-IM cable, available from Crestron. Other high-quality/low skew CAT5e/CAT6 wiring may also be used with varying performance. The maximum cable length between the IM-WCVP and the IM-WCVI is 40 feet. System Configuration Refer to the latest version of the IM-RXV1 & IM-RXV3 guide (Doc. 6478), available from the Crestron website for iMedia system configuration instructions. Operations & Installation Guide ­ DOC. 6489 iMedia Wall Plate Control Panel: IM-WCVP · 9 iMedia Wall Plate Control Panel Crestron IM-WCVP Operation The IM-WCVP can be used to turn a system on or off, select a source, or adjust volume. Turn on the System Press the PC button to turn on the system with the PC signals routed to the iMedia receiver or press the VIDEO button to turn on the system with the video signals routed to the iMedia receiver. The associated LED will light to indicate the selected source. Press the PC button to route PC signals to the iMedia receiver or press the VIDEO button to route video signals to the iMedia receiver The associated LED will light to indicate the selected source. Turn the volume knob clockwise to raise the volume of the selected input; turn counterclockwise to lower the volume of the selected input. Press and hold the selected source button for five seconds. The source button LED will flash and then turn off. Select a Source Adjust Volume Turn off the System 10 · iMedia Wall Plate Control Panel: IM-WCVP Operations & Installation Guide ­ DOC. 6489 Crestron IM-WCVP iMedia Wall Plate Control Panel Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. IM-WCVP Troubleshooting TROUBLE SOURCE LED does not illuminate. POSSIBLE CAUSE(S) Not receiving power. CORRECTIVE ACTION Verify that the iMedia cable is connected to the IM-WCVI and the IM-WCVI is connected to the iMedia receiver. Push a source button to select a source. Verify iMedia output cable connection is secure. Incorrect power supply. Incorrect cable connection. (Continued on following page) Operations & Installation Guide ­ DOC. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron website periodically for manual update availability and its relevance. Updates are identified as an "Addendum" in the Download column. Operations & Installation Guide ­ DOC. [. . . ] Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties. Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered trademark of Microsoft Corporation. [. . . ]