User manual CRESTRON IO TPMC-8X-BTP

[. . . ] 4 Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 More Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Best results occur if the TPMC-8X-BTP is stored at an optimal temperature of 32° to 104°F (0° to 40°C). After an extended period of storage, initiate a few charge/discharge cycles to restore full capacity. Operations & Installation Guide ­ DOC. 6556 Internal Battery Pack: TPMC-8X-BTP · 3 Internal Battery Pack for TPMC-8X Crestron TPMC-8X-BTP Setup Charging NOTE: A Lithium Ion (Li-Ion) battery typically provides 300-500 charge/discharge cycles. There are two ways to charge the TPMC-8X-BTP: · Install the TPMC-8X-BTP in a TPMC-8X touchpanel and connect the touchpanel to an AC source using its AC adapter or · Install the TPMC-8X-BTP in a TPMC-8X touchpanel and mount the touchpanel on an AC powered TPMC-8X-DS Docking Station/Charger (sold separately). NOTE: The battery pack may take up to three hours to charge in a powered touchpanel if the panel is in use during charging. NOTE: When the external battery pack (TPMC-8X-BTPE, sold separately) is attached, both the internal and external battery packs charge simultaneously. Installation Use the following procedure to install the TPMC-8X-BTP in a TPMC-8X touchpanel: 1. Place the touchpanel screen-side down on a clean, soft surface. Remove the two Phillips head screws that hold the internal battery compartment cover on the rear of the touchpanel. Place the TPMC-8X-BTP in the battery compartment oriented so the multi-pin connector is in the upper left corner. Carefully connect the multi-pin connector of the TPMC-8X-BTP with the corresponding connector inside the battery compartment (refer to illustration on the following page). 4 · Internal Battery Pack: TPMC-8X-BTP Operations & Installation Guide ­ DOC. 6556 Crestron TPMC-8X-BTP Internal Battery Pack for TPMC-8X TPMC-8X-BTP in Battery Compartment of TPMC-8X NOTE: To prevent battery drain during shipment or for long-term storage, the TPMC-8X has a battery switch inside the battery compartment. To use the internal battery, move the switch to the up (on) position. To conserve battery power when the unit will not be used for extended periods, move the switch to the down (off) position. (Refer to illustration on the following page. ) Operations & Installation Guide ­ DOC. 6556 Internal Battery Pack: TPMC-8X-BTP · 5 Internal Battery Pack for TPMC-8X TPMC-8X Internal Battery Switch Crestron TPMC-8X-BTP 5. Re-attach the battery compartment cover using the two supplied Phillips head screws. Removal Use the following procedure to remove the TPMC-8X-BTP from a TPMC-8X touchpanel: 1. Place the touchpanel screen-side down on a clean, soft surface. Remove the two Phillips head screws that hold the internal battery compartment cover on the rear of the touchpanel. Using the flat end of a small slot head screwdriver, gently pry the multi-pin connector off the corresponding connector in the battery compartment of the TPMC-8X. With the multi-pin connector detached from the TPMC-8X, lift the TPMC-8X-BTP out of the battery compartment. 6 · Internal Battery Pack: TPMC-8X-BTP Operations & Installation Guide ­ DOC. 6556 Crestron TPMC-8X-BTP Internal Battery Pack for TPMC-8X More Information Reference Documents The latest version of all documents mentioned within the guide can be obtained from the Crestron website (http://www. crestron. com/manuals). This link will provide a list of product manuals arranged in alphabetical order by model number. [. . . ] warrants its products to be free from manufacturing defects in materials and workmanship under normal use for a period of three (3) years from the date of purchase from CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and overlay components are covered for 90 days; batteries and incandescent lamps are not covered. This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if any. CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended or if it has been subjected to misuse, accidental damage, modification or improper installation procedures. [. . . ]