User manual CRESTRON IRP2

[. . . ] 8168A Infrared Emitter · 1 Infrared Emitter Crestron IRP2 Package Contents In addition to the IRP2, this package also contains an IR mask and twosided transparent tape. Installation Attach the IRP2 to the IR Sensor Window Refer to the following instructions and illustration. Identify the clear, flat bottom surface of the IRP2 shell. Apply transparent silicon adhesive (not supplied) to the flat side of the IRP2 or use the supplied transparent tape. CAUTION: Test the silicon adhesive on a non-visible area to confirm that it will not damage material or equipment. [. . . ] The high output side of the IRP2 Installation Guide - DOC. 8168A Infrared Emitter · 3 Infrared Emitter Crestron IRP2 shell permits control at this greater distance. Placement of the IRP2 on surfaces just above or below the IR sensor window, as shown in the following illustrations, may provide a more pleasing aesthetic appearance. However, be sure to position the IRP2 shell so that the edge of the component does not block the IR signal. NOTE: Placing the IRP2 shell on a cabinet door may result in interruption of the IR signal if the door is opened. Possible mounting locations of the IRP2 shell include being attached to a shelf directly below or above the IR sensor window. Front View Side View Connect the IRP2 Insert the two-pin connector of the IRP2 into an infrared - serial output port of the control system as shown in the following illustration. 4 · Infrared Emitter Installation Guide ­ DOC. 8168A Crestron IRP2 Infrared Emitter NOTE: The white-traced wire connects to the pin labeled S. Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (http://www. crestron. com) for a listing of Crestron worldwide offices. You can also log onto the online help section of the Crestron website to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. Installation Guide - DOC. 8168A Infrared Emitter · 5 Infrared Emitter Crestron IRP2 As of the date of manufacture, the IRP2 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Future Updates As Crestron improves functions, adds new features, and extends the capabilities of this product, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron website periodically for manual update availability and its relevance. Updates are identified as an "Addendum" in the Download column. 6 · Infrared Emitter Installation Guide ­ DOC. 8168A Crestron IRP2 Infrared Emitter Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ] Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supercedes all previous warranties. Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. [. . . ]