User manual CRESTRON IW CLW-SW1RF 4RF SWS1RF 4RF SLVS1RF

[. . . ] infiNETTM SWITCHES Introduction Features and Functions The CLW-SW1RF (-SW1RF) and CLW-SW4RF (-SW4RF) are stand-alone wall box switches that can also act as wireless infiNETTM devices that report to a Crestron® control processor through an infiNET gateway such as the Crestron C2N-MNETGW. These switches are a part of Crestron's line of lighting products using infiNET mesh network technology. infiNet technology is "Wi-Fi" friendly and provides fault tolerance and increased effective signal strength as network devices are added. Up to 30 infiNET devices (including C2N-MNETRPT infiNET Repeaters) can communicate with one C2N-MNETGW Gateway. [. . . ] For easy installation, Crestron recommends using 3 ½" deep wallboxes. Several devices can be installed in one wall box (multigang). This requires the removal of side sections (refer to diagram on page 4) and the derating of the switching device. For a smooth appearance, one-piece multigang faceplates (not supplied) can be installed. Other Switch Devices: Mechanical 3- or 4-way switches will not work with the -SW1RF, -SW4RF, -SWS1RF, -SWS4RF, and -SLVS1RF. Spacing: If mounting one device above another, leave at least 4 ½" vertical space between them. Derating Information for Incandescent, Tungsten Halogen, and Electronic Low Voltage Applications Part Number No Side Removed 1000W 1000W One Side Removed 700W 700W No Derating Necessary Two Sides Removed 550W 550W -SW1RF/ -SW4RF -SWS1RF/ -SWS4RF -SLVS1RF · Derating Information for Magnetic Low Voltage and Neon/Cold Cathode Applications* Part Number -SW1RF/ -SW4RF -SWS1RF/ -SWS4RF -SLVS1RF * No Side Removed 1000VA/ 750W 1000VA/ 750W One Side Removed 700VA/ 500W 700VA/ 500W Two Sides Removed 550VA/ 400W 550VA/ 400W · Multigang Installations In multigang installations, several controls are grouped horizontally in one wallbox. For a smooth appearance, one-piece multigang faceplates (not supplied) can be installed. When combining controls in a wallbox, remove inner side sections prior to wiring (refer to the following figure). Inner Sections of Multiganged Switches (CLW-SW4RF Shown) REMOVE INNER SECTIONS No Derating Necessary VA ratings are for input power to the transformer. If you do not know the input power requirement of the transformer, use the bulb's wattage rating to determine proper rating. Derating Information for Fluorescent/HID Applications Part Number -SW1RF/ -SW4RF -SWS1RF/ -SWS4RF -SLVS1RF No Side Removed 8A 8A One Side Removed 5. 5A 5. 5A No Derating Necessary Two Sides Removed 4. 5A 4. 5A Derating Information for Ceiling Fans Part Number -SW1RF/ -SW4RF -SWS1RF/ -SWS4RF RUN SET OFF RUN SET OFF No Side Removed 3A 3A One Side Removed 3A 3A Two Sides Removed 3A 3A -SLVS1RF No Derating Necessary 2. To remove a side section, bend the side section back and forth with a pair of pliers until the section breaks off from the mounting plate. Use a file or sandpaper to remove any excess metal. DO NOT REMOVE OUTER SECTIONS The load capacity must also be derated. The following charts provide derating information for various applications. 4 · infiNETTM Wall Box Switch : CLW-SW1/4RF, SWS1/4RF, & SLVS1RF Installation Guide - DOC. 6293A infiNETTM SWITCHES 3. Installation WARNING: Turn off power at the circuit breaker. Installing with power on can result in serious personal injury and damage to the device. NOTE: The -SW1RF, -SW4RF, -SWS1RF, and -SWS4RF require a neutral wire for operation. If no neutral is present, the device will not work. If no neutral is present, contact a licensed electrician for installation. NOTE: The -SWS1RF and -SWS4RF must be installed in the same wallbox that contains the connections to the load. NOTE: New installations should be checked for short circuits prior to installing the -SW1RF, -SW4RF, -SWS1RF, -SWS4RF, or -SLVS1RF. With power off, close the circuit and restore power. NOTE: Since the -SWS1RF or -SWS4RF is installed without a -SLVS1RF, the BLUE lead (Slave) should be capped. Other Wiring For another scenario that may be encountered during installation, refer to Figure 2 on page 8. 6293A infiNETTM Wall Box Switch: CLW-SW1/4RF, SWS1/4RF, & SLVS1RF · 5 infiNETTM SWITCHES Testing NOTE: The device may be warm to the touch during operation. [. . . ] While holding the pushbutton (hold "UP" on the -SW1RF and -SWS1RF, or hold Button 1 on the -SW4RF or -SWS4RF), move the mode selection switch to the "SET" position and back to the "RUN" position. The LED will flash once to confirm that the default values have been restored. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials and workmanship under normal use for a period of three (3) years from the date of purchase from CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and overlay components are covered for 90 days; batteries and incandescent lamps are not covered. This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON dealer. [. . . ]