User manual CRESTRON LEPB-5

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. INSTALLATION INSTRUCTIONS DI-000-PE400-00B Figure 1A: Surface Mounting Figure 1B: Flush Mounting Power Extender Dimming Control Cat. PE400-1 Rating: 1000W/VA 120VAC, 60Hz For use with Electronic Low-Voltage and Incandescent fixtures 1900 Box 1900 Box 2 Gang Raised Cover Raised Cover Mounting Screws (4 Places) 2 Gang Raised Cover Raised Cover Mounting Screws (4 Places) TOP TOP Power Extender Power Extender Wallplate Power Extender Power Extender Wallplate Figure 2: End View Figure 3: Front View Figure 4: Front View Spacing TOP INSTALLATION INSTRUCTIONS TOP CONTROL NEUTRAL NEUTRAL LOAD HOT SWITCH HOT 4-1/2" (11. 4 cm) Minimum TOP WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS. LIMITED 2 YEAR WARRANTY AND EXCLUSIONS Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for two years from the purchase date. [. . . ] WITH ALUMINUM WIRE USE ONLY DEVICES MARKED CO/ALR OR CU/AL. NOTE: The Power Extender must be installed in a 1900 Box with Raised Cover or a properly grounded metal 2-gang wall box, 3. 5" (8. 9 cm) deep (refer to Figure 1A and1B). Depending on the application and the number of connections, more space may be needed. If so, use an appropriate size box or box extension. WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKERS OR FUSES AND TEST THAT POWER IS OFF BEFORE WIRING!MORE THAN ONE CIRCUIT BREAKER CAN POWER THIS DEVICE. DISCONNECT "ALL" POWER SOURCES BEFORE SERVICING CONTROL. Remove 1/2" (1. 3 cm) of insulation from each circuit conductor in wall box. Make sure that ends of conductors are straight. Connect lead wires per appropriate WIRING DIAGRAM and FIGURE 2 as follows: All connections to the output terminals should be made using #12 AWG wire. Each power terminal can accept up to two(2) #12 wires. The recommended installation torque is 9. 0 in. -lbs. Carefully position all wires to provide room in wall box for Power Extender. When mounting, all PEAUXS must be spaced 4-1/2" above and below each unit for proper ventilation and heat dissipation (refer to Figure 4). Line voltage wiring should be at least 6 ft. away from sound or electronic equipment wiring. Mount Power Extender to outlet box with "TOP" facing up (refer to Figure 3). For Wall Box Mounting: Refer to Figure 1A. [. . . ] Adjust the dimmer (zone) BRIGHTNESS level. Activating the air gap on the dimmer will cause the PE400 to turn its controlled Load OFF. Wiring Diagram 1 120V Single Feed Wiring Application Wiring Diagram 2 120V Dual Feed Wiring Application Used if Dimmer/Switch has Neutral connection ( Hot (Black) (120VAC) ) Used if Dimmer/Switch has Neutral connection ( Hot (Black) Line 1 (120VAC) ) (Load) (Load) D3206/08 Controller/Dimmer CONTROL Incandescent Dimmer Neutral 1 (White) D3206/08 Controller/Dimmer CONTROL NEUTRAL NEUTRAL Incandescent Dimmer NEUTRAL NEUTRAL SWITCH HOT SWITCH HOT LOAD LOAD The PE400 has an air gap relay built in, therefore, the Load will be disconnected by an air gap when the dimmer is OFF or the air gap control on the dimmer is activated. TROUBLESHOOTING · The Power Extender is not powered - Circuit breaker is OFF. - Power wires are not connected properly. [. . . ]