User manual CRESTRON MMK-1000L WMKM-1000L

[. . . ] NOTE: If necessary, consult the latest revision of the Series 1000 Operations Guide (Doc. 5813) for a complete list of mounting options. Supplied Hardware The MMK-1000L consists of three parts. These parts produce an assembly that attaches to the PMK-1000L or BB-1000L. The WMKM-1000L consists of the same three parts that make up the MMK-1000L as well as one mounting plate. [. . . ] Apply drywall joint compound as needed to finish the cutout. When dry, the Series 1000 touchpanel can be installed using the four tapped holes in the PMK-1000L. Refer to the latest revision of the Series 1000 Operations Guide (Doc. 5813) for details. WMKM-1000L Procedure The procedure in this section provides the necessary steps for the assembly and installation of the WMKM-1000L into a wall. Complete the steps in the order provided. The only tools or materials required and not supplied are a drywall saw or equivalent, a level, four standard drywall screws, #2 Phillips screwdriver, and tools/material to apply drywall joint compound. Insert the two pins on one fastener plate into the top two outer holes on the mounting plate, as shown in the illustration after this step. PUSH-ON FASTENER QTY. 4 Create the Fastener/Mounting Plate Assembly MOUNTING PLATE QTY. 1 FASTENER PLATE QTY. 2 4 · Mud Mount Kits: MMK-1000L & WMKM-1000L Installation Guide ­ DOC. 6062 Crestron MMK-1000L & WMKM-1000L 2. Mud Mount Kits Slide a push-on fastener over each pin on the top fastener plate. Do not push the fasteners all the way down onto the pins. Slide them on enough to keep the fastener plate and mounting plate as one fastener/mounting plate assembly. This allows for minor mounting adjustments. Use the second fastener plate and repeat steps 1 and 2 on the lower part of the mounting plate. Locate an area on the wall that is free of miscellaneous wiring and studs. Make a small hole near the middle of the designated site; verify that the location is suitable. 3. 5. NOTE: Make the cutout as level as possible. The mounting plate allows for only minor leveling adjustments. Use the drywall saw or equivalent to produce a level, square cutout in the drywall that measures 4½ inches wide (114 mm) x 4½ inches high (114 mm). Insert the symmetrical mud ring plate into the opening, as shown in the illustration after this step. 7. Insert the Mud Ring Plate into the Opening MUD RING DRYWALL CUTOUT: 412 in WIDE x 412 in HIGH (114 mm WIDE x 114 mm HIGH) 8. Carefully pass the fastener/mounting plate assembly through the opening and rest the assembly against the interior surface of the Installation Guide ­ DOC. 6062 Mud Mount Kits: MMK-1000L & WMKM-1000L · 5 Mud Mount Kits Crestron MMK-1000L & WMKM-1000L drywall. Verify that the fastener plates are between the mounting plate and the drywall. When the fastener/mounting plate assembly is in position, bend the top two flanges of the mud ring upward (approximately 90 degrees) and the bottom two flanges downward (approximately 90 degrees). Refer to the illustration after this step. NOTE: Fastener/mounting plate assembly will have slight play; this is normal. [. . . ] Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. [. . . ]