User manual CRESTRON MMK-2000L WMKM-2000L

[. . . ] NOTE: If necessary, consult the latest revision of the TPS-2000L Operations Guide (Doc. 5972) for a complete list of mounting options. Supplied Hardware The MMK-2000L consists of three items with differing quantities. These items produce an assembly that attaches to the PMK-2000L or BB-2000L. The WMKM-2000L consists of the same three items that make up the MMK-2000L as well as one mounting plate. [. . . ] Apply drywall joint compound as needed to finish the cutout. When dry, the TPS-2000L can be installed using the four tapped holes in the PMK-2000L. Refer to the latest revision of the TPS-2000L Operations Guide (Doc. 5972) for details. WMKM-2000L Procedure The procedure in this section provides the necessary steps for the assembly and installation of the WMKM-2000L into a wall. Complete the steps in the order provided. The only tools or materials required and not supplied are a drywall saw or equivalent, a level, four standard drywall screws, #2 Phillips screwdriver, and tools/material to apply drywall joint compound. Insert the two pins on one fastener plate into the top two outer holes on the mounting plate, as shown in the illustration after this step. Create the Fastener/Mounting Plate Assembly MOUNTING PLATE QUANTITY 1 PUSH-ON FASTENER QUANTITY 4 FASTENER PLATE QUANTITY 2 2. Slid two push-on fasteners over the pins on the fastener plate to loosely secure the fastener plate and the mounting plate. Do not push the pushon fasteners all the way down onto the pins. Slid them on enough to keep the fastener plate and mounting plate as one fastener/mounting plate assembly. Use the second fastener plate and repeat steps 1 and 2 on the opposite side of the mounting plate. 3. 4 · Mud Mount Kits: MMK-2000L & WMKM-2000L Installation Guide ­ DOC. 6025 Crestron MMK-2000L & WMKM-2000L 4. 5. Mud Mount Kits Locate an area on the wall that is free of miscellaneous wiring and studs. Make a small hole near the middle of the designated site; verify that the location is suitable. NOTE: Make the cutout as level as possible. The mounting plate allows for only minor leveling adjustments. Use the drywall saw or equivalent to produce a level, rectangular cutout in the drywall that measures 6 3/8 inches wide (16. 159 cm) x 4 ½ inches high (11. 389 cm). Insert the symmetrical mud ring plate into the opening, as shown in the illustration after this step. 7. Insert the Mud Ring Plate into the Opening MUD RING PLATE QUANTITY 1 8. OPENING IN DRYWALL Carefully pass the fastener/mounting plate assembly through the opening and rest the assembly against the interior surface of the drywall. Verify that the fastener plates are between the mounting plate and the drywall. Refer to the illustration after this step for visual guidance. Installation Guide ­ DOC. 6025 Mud Mount Kits: MMK-2000L & WMKM-2000L · 5 Mud Mount Kits Crestron MMK-2000L & WMKM-2000L Fastener Plates Located Between Mounting Plate and Drywall FASTENER/ MOUNTING PLATE ASSEMBLY INSERTED MUD RING PLATE 9. When the fastener/mounting plate assembly is in position, bend the top two flanges of the mud ring upward (approximately 90 degrees) and the bottom two flanges downward (approximately 90 degrees). Refer to the illustration after this step. NOTE: Fastener/mounting plate assembly will have slight play; this is normal. It allows for minor adjustments to the TPS-2000L during installation. Bend Flanges BEND FLANGES UP APPROXIMATELY 90° BEND FLANGES DOWN APPROXIMATELY 90° 6 · Mud Mount Kits: MMK-2000L & WMKM-2000L Installation Guide ­ DOC. [. . . ] Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. [. . . ]