User manual CRESTRON PG TOUCH THE PC V1

[. . . ] This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Crestron Serial Mouse Control Driver Software Contents Serial Mouse Control Driver Introduction Driver Requirements Quickstart Procedure Driver Software Installation Configuring the System PC to Touchpanel Serial Communication PC to Touchpanel Cresnet Communication PC to Touchpanel Ethernet Communication SIMPL Windows Programming VT Pro-e Programming Problem Solving Troubleshooting Further Inquiries Future Updates Future Firmware Upgrades Appendix 1 - Keyboard Functionality Appendix 2 - Additional PC and Mouse Functions Appendix 3 - Cable and Wiring Specifications Cresnet 4-Wire Wiring Crestron RJ45 Cabling DB9F Adapter and RJ11 Modular Cable DB9F to RJ11 Cable Fabrication Software License Agreement Return and Warranty Policies Merchandise Returns / Repair Service CRESTRON Limited Warranty 1 1 2 2 3 5 5 7 9 13 16 19 19 22 22 22 23 24 25 25 26 26 27 28 30 30 30 Programmer's Guide - DOC. 5916A Serial Mouse Control Driver · i Crestron Serial Mouse Control Driver Software Serial Mouse Control Driver Introduction The Crestron Serial Mouse Control Driver, licensed for use only in conjunction with the TPS-XVGA/-BV/L Computer Interface Cards, is designed to enable a Crestron Isys TPS touchpanel to function as a touch-sensitive computer monitor, compatible with Microsoft Windows 98/XP and Windows 2000/NT. When you use the touchpanel as a monitor for a computer connected to your Crestron system, the Serial Mouse Control Driver lets you control the cursor movement and simulate the functions of a traditional mouse using your finger on the touchpanel to simulate typical computer mouse click and drag functions. [. . . ] Serial Mouse Control Driver is disabled. Uninstall then re-install mouse driver. Right-click on system tray icon and select Enabled. (Enabled will be checked not X'ed. ) Non-Microsoft serial Disable the conflicting driver. (It may be driver does not work necessary to uninstall & re-install Serial Mouse Control Driver. ) with Serial Mouse Control Driver. Touchpanel was not For Serial Configuration: 1. From the Crestron Viewport, establish initialized properly. communication with the TPS console and use the "touch output format" command (toformat) to verify mouse control - type toformat mouse and press <ENTER>. Verify the setting type toformat and press <ENTER>. This should display "Current Touchout Format: PC Mouse. " * 2. Use the "RS-232 touch output" command (touchout) to reserve the RS-232 port for touch screen output type RS232 touchout and press <ENTER>. Verify the setting - type RS232 and press <ENTER>. This should display "Current RS-232 Mode: TouchOutput. " * Reboot touchpanel. Programmer's Guide - DOC. 5916A Serial Mouse Control Driver · 19 Software Crestron Serial Mouse Control Driver Serial Mouse Control Driver Troubleshooting (continued) TROUBLE (Continued) No cursor movement. POSSIBLE CAUSE(S) CORRECTIVE ACTION Touchpanel is not generating packets (no cursor movement). (Continued) 3. Use the "touch output destination" Touchpanel was not command (todest) to verify RS-232 initialized properly. type todest RS232 and press <ENTER>. Then verify the setting type todest and press <ENTER>. This should display "Current Touchout Destination: RS-232". * For Cresnet or Ethernet Configuration: 1. From the Crestron Viewport, establish communication with the TPS console and use the "touch output format" command (toformat) to verify mouse control - type toformat mouse and press <ENTER>. Verify the setting type toformat and press <ENTER>. This should display "Current Touchout Format: PC Mouse. " * 2. Use the "touch output destination" command (todest) to verify Cresnet type todest cresnet and press <ENTER>. Then verify the setting type todest and press <ENTER>. [. . . ] Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. [. . . ]