User manual CRESTRON RG 2-SERIES CONTROL SYSTEMS

[. . . ] Crestron 2-Series Control Systems Reference Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2006 Crestron Electronics, Inc. Crestron 2-Series Control Systems Reference Guide Contents 2-Series Control Systems 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Programming Tools & Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] NOTE: Compact flash directories can only use the standard DOS file wildcards. Help Menu(s): Syntax: Parameters: Possible Source: Minimum CUZ: File DELete filespec filespec ­ ASCII string contains the file name and/or wildcards RS-232, CTP, Telnet, User Program 1. 001 Processor Group: All Processors DHCP Description: Help Menu(s): Syntax: Parameters: This command selects whether dynamic IP addressing is supported using the DHCP protocol. If enabled, a HOSTNAME should also be entered. Entering the command without a parameter displays the current setting. Ethernet DHCP [ON | OFF | STATUS | REL_RENEW] ON ­ enables DHCP operation OFF ­ disables DHCP operation (default) STATUS ­ display the DHCP status REL_RENEW ­ perform a release and renew function on the DHCP connection Possible Source: Minimum CUZ: RS-232, CTP, Telnet, User Program 3. 044 Processor Group: Ethernet Processors (continued on next page) Reference Guide ­ DOC. 6256A 2-Series Control Systems · 97 Reference Guide Crestron 2-Series Control System 2-Series Console Commands (continued) DIR Description: This command lists information about file(s) from the file system. Wildcards are accepted and can be in the form of (*file, file, and file). If no parameter is entered, all files are listed. NOTE: Compact flash directories can only use the standard DOS file wildcards. Help Menu(s): Syntax: Parameters: Possible Source: Minimum CUZ: File DIR [filespec] filespec ­ ASCII string contains the file name and/or wildcards RS-232, CTP, Telnet, User Program 1. 001 Processor Group: All Processors DOMAINNAME Description: This command sets the domain name to be used in a DHCP environment. It is used to re-establish the connection to the processor when DHCP is enabled through the NAT configuration pages. Entering the command without a parameter displays the current setting. Ethernet DOMAINNAME domainname domainname ­ ASCII string contains the domain in which the processor is a part (characters are limited to A-Z, a-z and `-`) Possible Source: Minimum CUZ: RS-232, CTP, Telnet, User Program 3. 044 Help Menu(s): Syntax: Parameters: Processor Group: Ethernet Processors ECHO Description: This command enables/disables character echoing on the console connection. If no parameter is entered, the current state is displayed. Echo is also available if an empty command string is sent to the console. Entering the command without a parameter displays the current setting. System ECHO [ON | OFF] ON ­ enables character echoing OFF ­ diables character echoing (default) Possible Source: Minimum CUZ: RS-232, CTP, Telnet 1. 001 Help Menu(s): Syntax: Parameters: Processor Group: All Processors EEPROM Description: Help Menu(s): Syntax: Parameters: Possible Source: Minimum CUZ: This command displays the current parameters stored in EEPROM. Device Eeprom none RS-232, CTP, Telnet, User Program 1. 001 Processor Group: All Processors (continued on next page) 98 · 2-Series Control Systems Reference Guide ­ DOC. 6256A Crestron 2-Series Control Systems Reference Guide 2-Series Console Commands (continued) ERRLOG Description: This command prints a list of the most recent errors. It wraps around at 100 so only the last 100 entries into the log are displayed. NOTE: Refer to "Appendix D: Error Message Definitions" on page 123 for a list and description of error messages that can be generated by a 2-Series control system. Help Menu(s): Syntax: Parameters: Possible Source: Minimum CUZ: System ERRlog none RS-232, CTP, Telnet, User Program 1. 001 Processor Group: All Processors ESTATUS Description: Help Menu(s): Syntax: Parameters: Possible Source: Minimum CUZ: This command displays the status of the Ethernet link (Link on/off, link speed, full duplex on/off). [. . . ] The failure of either party to enforce any right or take any action in the event of a breach hereunder shall constitute a waiver unless expressly acknowledged and set forth in writing by the party alleged to have provided such waiver. 178 · 2-Series Control Systems Reference Guide ­ DOC. 6256A Crestron 2-Series Control Systems Reference Guide If You are a business or organization, You agree that upon request from Crestron or its authorized agent, You will within thirty (30) days fully document and certify that use of any and all Software at the time of the request is in conformity with Your valid licenses from Crestron of its authorized agent. Without prejudice to any other rights, Crestron may terminate this Agreement immediately upon notice if you fail to comply with the terms and conditions of this Agreement. In such event, you must destroy all copies of the Software and all of its component parts. PROPRIETARY RIGHTS Copyright. [. . . ]