User manual CRESTRON ST-1550C

[. . . ] Crestron ST-1550C 1-Way Wireless RF Touchpanel Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2005 Crestron Electronics, Inc. Crestron ST-1550C 1-Way Wireless RF Touchpanel Contents 1-Way Wireless RF Touchpanel: ST-1550C 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functions and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] . F0. Touchpanel "Device Settings" Window ST-1550C Symbol in Programming Manager Programming Manager is where programmers "program" a Crestron control system by assigning signals to symbols. The following diagram shows the ST-1550C symbol in the SIMPL Windows' Programming Manager. Operations Guide ­ DOC. 6096A 1-Way Wireless RF Touchpanel: ST-1550C · 15 1-Way Wireless RF Touchpanel Crestron ST-1550C Detail View of the ST-1550C in SIMPL Windows' Programming Manager The following table lists and gives functional descriptions for the touchpanel outputs. Symbol Output Signal Descriptions OUTPUT press 1 through press 32 DESCRIPTION Notifies control system of button press (1 ­ 32). High/1 = Button being pressed Low/0 = Button not being pressed Programming with VT Pro-e Control screen variations incorporating two- and three-dimensional graphics and text are possible and can be created with VT Pro-e, a design/programming Windows -based software program. A set of pages, which make up a project, can be designed for each application. Each touchpanel can be organized with the ideal, color-oriented control environment with custom control graphics: icons, two and three-dimensional buttons, and floor plans. The project is uploaded to the touchpanel's flash PROM. The touchpanel uses the project until another is uploaded from the PC. The PC may be disconnected from the control processor except when uploading a project. For additional software information, refer to the help file provided with the software. The latest version of VT Pro-e can be obtained from the Crestron website. Virtual Feedback Programming a one-way RF touchpanel such as the ST-1550C requires consideration of "feedback. " Since the panels are one-way only, and there is no true feedback, you must create "virtual feedback" so that buttons respond appropriately when pressed and the user perceives no real difference between a one-way panel and a two-way panel. The SystemBuilder takes care of all of this for you. However, if you are programming your panels with SIMPL Windows and VT Pro-e, you must follow the following procedure to add logic both to the touchpanel for button feedback and to the control system program to properly process the signals, and to make sure that the state of the buttons on the panel and in the control system remain in sync. 16 · 1-Way Wireless RF Touchpanel: ST-1550C Operations Guide ­ DOC. 6096A Crestron ST-1550C 1-Way Wireless RF Touchpanel Button press feedback produces a change in appearance from the inactive state to the active state, or vice versa, as defined in the program. · · · Momentary feedback, from inactive to active and back to inactive, has a short duration, lasting only as long as the button is pressed. Toggle feedback produces a change of state each time the button is pressed (a logical active vs. With Interlock feedback, only one button in an assigned interlock group can be active at a time. Pressing an inactive button changes its state to active, and forces the other buttons in the group to inactive. (To clear all buttons in the interlock group requires that an extra button be added whose sole purpose is to force all the others to the inactive state. ) Duration feedback is assigned to a group of buttons that are to be activated simultaneously, remain active for a specified period of time, and then return to the inactive state. · In the following paragraphs, each feedback type will be discussed in detail as applicable. VT Pro-e Procedures Buttons requiring feedback need to have the feedback type assigned as if it were a property of the object. Button feedback logic is classified as momentary, toggle, interlock, or duration. Logic is added to the buttons on the panel (after join numbers and other properties have been assigned), by right clicking the button in VT Pro-e and selecting Feedback, which displays the "Feedback" window. "Feedback" Window NOTE: When the Feedback window is open, you can click on any of the buttons on the page and view their various feedback properties. Operations Guide ­ DOC. 6096A 1-Way Wireless RF Touchpanel: ST-1550C · 17 1-Way Wireless RF Touchpanel Crestron ST-1550C Interlock An interlock consists of a number of assigned buttons grouped together so that button selection is mutually exclusive within the group. [. . . ] Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. [. . . ]