User manual CRESTRON ST-DSN

[. . . ] 5 Problem Solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Further Inquiries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Future Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] In either case, the ST-DSN monitors the ST-BTPN status and waits for the correct conditions to start a fast charge. The LED remains ON during a fast charge. RDY (Ready) Illuminates when the ST-BTPN in the ST-DSN cavity is fully charged. 4 · Docking Station: ST-DSN Operations Guide ­ DOC. 6095 Crestron ST-DSN Industry Compliance Docking Station As of the date of manufacture, the ST-DSN has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Setup Power Source The DC power socket connector on the bottom of the unit is used to supply power via an external power pack that Crestron supplies with the ST-DSN. It is the PW1215 (110v USA and Canada) or PWI-1215 (220v International). If an external power pack other than these Crestron models is used, verify that it meets the required specifications and polarity as shown below. Power Pack Specifications CRESTRON POWER PACK PW-1215 PWI-1215 INPUT SPECS 120VAC, 60Hz, 35W 220VAC, 50Hz, 35W OUTPUT SPECS 12VDC, 1500mA 12VDC, 1500mA, 18VA Power Pack Polarity Using the ST-DSN to Charge the ST-BTPN (Rechargeable Battery Pack) WARNING: The ST-BTPN is shipped fully discharged. Charge the ST-BTPN in a well-ventilated area away from sparks, open flame, or smoke. WARNING: Avoid damage to the ST-BTPN and possible physical harm, use only the specified external power pack PW-1215 (110v) or PWI-1215 (220v) or equivalent when charging with the ST-DSN. There are three possible methods of charging the ST-BTPN with the ST-DSN. All methods are considered fast charging and take between 2. 7 and 6 hours for a fully discharged ST-BTPN. Using the touchpanel during charging may take up to 6 hours and is only permissible with certain Crestron wireless touchpanel models. Operations Guide ­ DOC. 6095 Docking Station: ST-DSN · 5 Docking Station Crestron ST-DSN NOTE: For more information on charging times, refer to the latest revision of the Rechargeable Battery Pack Operations & Installation Guide (Doc. 6088), "Specifications" section. NOTE: Make sure that the contacts of the ST-DSN and ST-BTPN touch. The CHG LED illuminates while the ST-BTPN is charging. When the ST-BTPN is fully charged, the CHG LED goes out and the RDY LED illuminates. Method 1: ST-BTPN Alone NOTE: Use the optional charging guide when charging the ST-BTPN alone (while it is not installed in the touchpanel). Position the charging guide into the ST-DSN cavity. Position the ST-BTPN, by itself, into the ST-DSN cavity to automatically initiate charging. Refer to the illustration below to confirm positioning. Charging the ST-BTPN (Alone) ST-DSN SHOWN WITH CHARGING GUIDE Contacts ST-BTPN RECHARGABLE POWER PACK DO NOT PLACE METALLIC OBJECTS (COINS, PAPER CLIPS, ETC. ) OR LIQUIDS IN THIS AREA; PRODUCT DAMAGE WILL RESULT. ONLY CRES TRON USE THE POWER PACK SPECIFIED FOR THIS UNIT. Crestron Electronics, Inc. Rockleigh, NJ 07647 BATTERY GUIDE MUST BE USED WHEN CHARGING BATTERY OUTSIDE TOUCH PANEL. Bottom view Flip battery to install CHG RDY Method 2: ST-BTPN Installed in an Inactive Touchpanel NOTE: Do not use the optional charging guide when charging the ST-BTPN while installed in the touchpanel. NOTE: This method only applies to the ST-1550C and ST-1700C wireless touchpanels. [. . . ] This warranty statement supercedes all previous warranties. Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered trademark of Microsoft Corporation. Windows95/98/Me/XP and WindowsNT/2000 are trademarks of Microsoft Corporation. Operations Guide ­ DOC. [. . . ]