User manual CRESTRON ST-LT

[. . . ] CRESTRON Contents Lutron Interface 1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Physical Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Leading Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The dialog box should appear as shown below; click OK. Function Dialog Box 14. Additional macros should be created and assigned for each button on the lighting page that provides a function. Therefore, repeat steps 6 through 13 for the appropriate buttons. 12 · Lutron Interface Operations Guide - Doc. 5694 CRESTRON SIMPL SIMPL is CRESTRON's programming language designed for easy implementation of the control system requirements. The best representation of SIMPL programming is the block diagram. A basic ST-LT SIMPL program is shown and described below. ST-LT SIMPL Program CT-1500 1 2 3 4 0 UNIT1-SCENE2 UNIT7+8-SCENE16 UNIT3-ZONE1- ST-COM :A21 :AG78 :D31 MV TRIG [TRIG*] OUT STOP-DOWN-ALL :E 0. 1s S-# UNIT3-ZONE1+ :B31 MV 0 TRIG [TRIG*] OUT STOP-UP-ALL :C NET. ID:03 0. 1s S-# NET. ID:04 BAUD=GRAFIK The sample ST-LT SIMPL program allows two scenes for the Grafik Eye; scene 2 on Main Unit 1 and scene 16 on Main Units 7 and 8. It also allows zone 3 to be ramped up and down. The MV symbols are used to detect the release of the UP and DOWN buttons which results in the transmission of the appropriate zone up/down stop commands. Workshop The CRESNET II Workshop is designed to simplify the various operations needed to program and run a CRESNET II control system. The series of screen displays shown below are accessible from the "Define Network" option of the SIMPL-I Menu in the CRESNET II Workshop. These screens are shown to clarify the means of assigning signal names for the SIMPL program in the previous illustration. ST-LT Workshop Screens (1 of 4) The ST-LT definition supports a subset of the ST-COM definition; use A_IN, A_OUT for serial string transmission as well as the regular "in" and "out" directions for hard-coding serial data. Operations Guide - Doc. 5694 Lutron Interface · 13 CRESTRON ST-LT Workshop Screens (2 of 4) ST-LT Workshop Screens (3 of 4) ST-LT Workshop Screens (4 of 4) The ST-LT is defined as an "ST-COM, Port A". Enter "GRAFIK" into the baud rate field to allow the ST-LT to communicate with the Grafik Eye unit. The fields for parity, data bits, and stop bits are not used and may be set to any value. If Port B is defined to be 9600 N81, a RS-232 link to the Grafik Eye unit through the RS-232 port on the back of the ST-LT is permitted. The RS-232 port is bidirectional; data can be transmitted and received to/from the Grafik Eye. Typically, this port is used for debugging only. A standard DB9 male/DB9 female straight-through cable is used to go from this port to a PC. 14 · Lutron Interface Operations Guide - Doc. 5694 CRESTRON The data field contains the command protocol for the Grafik Eye system. A description of commands, their operation, and examples are provided in the table below. Commands for GRX-AV-RS232 and GRX-AV-RS232/ATC OPERATION Select Scene Scene Lock CMD PARAMETERS A SL [scene][main units] [+]or[-][main units] EXAMPLES :A21 select scene 2 on unit 1 :AG78 select scene 16 on units 7 & 8 :SL release all units from scene lock :SL-6 release only unit 6 from lock :SL+45 additionall lockout units 4 & 5 Request Scene Status Sequence G SQ NONE [+]or[-][main units] :G report scene status of all units on link :SQ release all unitsfrom sequence mode :SQ-3 release only unit 3 from sequencing :SQ+68 add units 6 & 8 to sequencing Zone Lock ZL [+]or[-][main units] :ZL release all units from zone lock :ZL-1 release only unit 1 from lock :ZL+36 additionally lockout units 3 & 6 Zone Lower Zone Lower Stop Zone Raise Zone Raise Stop Set Time* Report Time* Select Schedule* Report Schedule* Report Sunrise/Sunset* Super Sequence Start* Super Sequence Pause* Super Sequence Resume* D E B C ST RT SS RS RA QS QP QC [main unit][zones] NONE [main unit][zones] NONE :D5 stop ramping down all zones on unit 5 :D3124 ramp down zones 1, 2 & 4 on unit 3 :E stop ramping down all zones on all units :B5 stop ramping up all zones on unit 5 :B3124 ramp up zones 1, 2 & 4 on unit 3 :C stop ramping up all zones on all units [hr][min][mth][day] :ST 1 35 10 26 95 5 set time and date to 1:35am, con. [yr][dayofweek] Thursday, October 26, 1995 NONE [schedule] NONE NONE NONE NONE NONE :RT report current time and date of control response ~:rt hr min month day yr dayofweek :SS1 start weekday schedule :RS which schedule is currently running response ~:rs schedule :RA report sunrise time and sunset time response ~:ra rise_hr rise_min set_hr set_min :QS start super sequence at first event :QP stop super sequence at current event :QC resume super sequence at next event NOTE: Command operations denoted with an asterisk (*) are for GRX-AV-RS2323/ATC only. For a more comprehensive description of commands refer to "Appendix: GRAFIK Eye Commands" on page 18. Operations Guide - Doc. 5694 Lutron Interface · 15 CRESTRON Problem Solving Troubleshooting The table below provides corrective action for possible trouble situations. [. . . ] Set time to 5:04 PM on October 31, 1995; the day of week is set to Tuesday. (RT) Report Time This command reports the current time and date of the internal timeclock. If this command is entered on a GRX-AV-RS232 unit, an error condition is issued. Example: :RT<CR> Report time . The response is ":rt" and then a string of numbers indicating the time and date in the same order that it would be entered using the set time command. Example of Responses: <CR><LF>~:rt 2 14 7 30 71 6 1 OK<CR><LF> <CR><LF>~:rt 17 4 10 31 95 3 1 OK<CR><LF> The time is 2:14 AM on July 30, 1971; the day of week is Friday. The time is 5:04 PM on October 31, 1995; the day of week is Tuesday. (SS) Select Schedule This command determines which schedule the GRX-AV-RS232/ATC is running. The GRX-AV-RS232/ATC executes the next event that was to occur in the schedule selected. [. . . ]