User manual CRESTRON ST-VS

[. . . ] Crestron ST-VS Video Sensor Module Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. © 2003 Crestron Electronics, Inc. Crestron ST-VS Video Sensor Module Contents Video Sensor Module: ST-VS 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features and Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This tree can be expanded to display and configure the communication ports. Expanded PRO2 System Tree C2Net-Device Slot in Configuration Manager To incorporate an ST-VS into the system, drag the ST-VS from the Cresnet Control Modules | Cresnet Sensing Modules folder of the Device Library and drop it in System Views. The PRO2 system tree displays the ST-VS in Slot 9, with a default Net ID of 3C as shown in the following illustration. NOTE: The first ST-VS in a system is preset with a Net ID of 3C when its symbol is dragged into the upper pane of System Views. Additional ST-VS units are assigned different Net ID numbers as they are added. Operations Guide ­ DOC. 5767A Video Sensor Module: ST-VS · 9 Video Sensor Module Setting the Net ID in Device Settings Crestron ST-VS Double-click the ST-VS icon to open the "Device Settings" window. This window displays the ST-VS device information. If necessary, select the Net ID tab to change the Net ID as shown in the following figure. ST-VS "Device Settings" Window NOTE: SIMPL Windows automatically changes the Net ID values of a device added to a program if a duplicate device or a device with the same default Net ID already exists in the program. Always ensure that the hardware and software settings of the Net ID match. For Net ID hardware setting details, refer to "Identity Code" on page 6. ST-VS Symbol in Programming Manager Programming Manager is where programmers "program" a Crestron control system by assigning signals to symbols. The following graphic shows the ST-VS symbol in the SIMPL Windows' Programming Manager. Detail View of the ST-VS in SIMPL Windows Programming Manager The ST-VS provides four discrete video sensors. The <sense> outputs go high whenever the presence of a video signal is detected at the corresponding input. 10 · Video Sensor Module: ST-VS Operations Guide ­ DOC. 5767A Crestron ST-VS Device Extenders Video Sensor Module To facilitate network functions and diagnostics, SIMPL Windows provides two device extenders for the ST-VS. The Poll Manager and The Poll Manager (2 Series Extended) symbols are device extenders for plug-in control cards and for Cresnet devices and touchpanels. The Poll Manager takes the device on and offline without need to physically disconnect it from the network, and reports the current connection status of the device. The device extenders are available with X-Series and 2-Series control systems; they are not available with the ST-CP or CN-Series control systems. To add a device extender, right-click the ST-VS in Program View, point to Insert Device Extender and select the desired device extender. To program a device extender, expand the ST-VS in Program View and drag the device extender to Detail View. Uploading Assuming a PC is properly connected to the entire system, Crestron programming software allows the programmer to upload programs and projects after their development to the control system. However, there are times when the files for the program and projects are compiled and not uploaded. Instead, compiled files may be distributed from programmers to installers, from Crestron to dealers, etc. In those instances, one has the option to upload via the programming software or to upload via the Crestron Viewport. NOTE: The Crestron Viewport is available as a pull-down command from SIMPL Windows and VT Pro-e (Tools | Viewport) or as a standalone utility. The Viewport utility performs multiple system tasks, primarily via an RS-232 or TCP/IP connection between the control system and a PC. [. . . ] Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be nonwarranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. [. . . ]