User manual CRESTRON STX-1700CXP PRE-SILVER

[. . . ] Crestron STX-1700CXP 2-Way RF Wireless Touchpanel Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2003 Crestron Electronics, Inc. Crestron STX-1700CXP 2-Way RF Wireless Touchpanel Contents 2-Way RF Wireless Touchpanel: STX-1700CXP 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functions and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Select the RF/IR ID tab to change the touchpanel RF ID, as shown below. For more information on setting the RF/IR ID, refer to "RF Setup" shown on page 9. Touchpanel "Device Settings" Window STX-1700CXP Symbol in Programming Manager Programming Manager is where programmers "program" a Crestron control system by assigning signals to symbols. The graphic after this paragraph shows the STX1700CXP symbol in the SIMPL Windows' Programming Manager. Operations Guide ­ DOC. 6144 2-Way RF Wireless Touchpanel: STX-1700CXP · 15 2-Way RF Wireless Touchpanel Crestron STX-1700CXP Detail View of the STX-1700CXP in SIMPL Windows' Programming Manager Signal Types Signals interconnect the various devices and logic symbols that comprise a SIMPL program. Signals can be one of three types: digital, analog, or serial. For any given signal, the signal type is determined by its driving source. That is, if the symbol that drives the signal has an analog output, then, by definition, the signal connected there will be an analog signal. In SIMPL Windows, the signal types are color-coded as follows: Digital = Blue Analog = Red Serial = Black Other = Green NOTE: "Other" signals are a combination of the three basic types (e. g. many symbols accept either analog or serial signals where the combination is shown as a green signal). The signal type is displayed on the Status Bar when the signal is highlighted. For additional information, refer to Doc. 6120, Crestron SIMPL Windows Symbol Guide. It may be downloaded from the Downloads | Product Manuals | Software section of the Crestron website (www. crestron. com). Digital Signals A digital signal contains one bit of information and usually takes on one of two values: 1 or 0. These two digits can represent the logical values true and false, and they can be represented in an electronic device by the states on/off or high/low, recognized as two voltage levels. (Other common descriptors are active/inactive. ) Analog Signals Unlike digital signals, analog signals can vary continuously in value, in the same manner as a parameter such as volume, temperature, or pressure. Analog signals contain 16 bits of information, which means that this type of signal can have values ranging from 0 to 65535 (216-1). This 16-bit property makes analog signals useful for 16 · 2-Way RF Wireless Touchpanel: STX-1700CXP Operations Guide - DOC. 6144 Crestron STX-1700CXP 2-Way RF Wireless Touchpanel controlling devices that do not have discrete settings, such as volume controllers, pan/tilt head controllers, and lighting dimmers. Serial Signals Serial signals are much like analog signals, in that they, too, contain 16 bits of information. However, whereas the value of an analog signal is used directly­to control volume or temperature, for instance­the value of the serial signal is used as a pointer to a location in memory that contains a string of characters. When a serial signal is routed to a symbol, that symbol can identify the signal as serial rather than analog and it will automatically look at the data to which it points. Thus, serial signals are used to facilitate the transmission of serial data (strings of characters). These signals can be generated by incoming data on a COM port or by a symbol that has a serial output. STX-1700CXP Input/Output Signals The STX-1700CXP symbol provides up to 4000 digital joins, up to 1024 analog joins, and up to 127 serial output joins and 255 serial input joins. [. . . ] Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. [. . . ]