User manual CRESTRON TPMC-10

[. . . ] Crestron TPMC-10 Isys i/OTM WiFi Touchpanel Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2006 Crestron Electronics, Inc. Crestron TPMC-10 Isys i/OTM WiFi Touchpanel Contents Isys i/OTM WiFi Touchpanel: TPMC-10 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functions and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 6284C Isys i/OTM WiFi Touchpanel: TPMC-10 · 29 Isys i/OTM WiFi Touchpanel Analog Input & Output Signal Descriptions (continued) Crestron TPMC-10 TOUCHPANEL SIGNAL NAME AND TYPE VT Pro-e JOIN TYPE VT Pro-e OBJECT DESCRIPTION Sends time values for display on the Timer object. Valid analog values can be signed or unsigned, depending on the selection made in VT Pro-e. Analog Feedback Join Unsigned values range from 0s to 65535s (18H:12M:15S). Timer Signed values for the HH:MM:SS format can range from -32767s (-09:06:07) to +32767s (+09:06:07). Unsigned values for the MM:SS format can range from 0s to 5999s (99:59). Signed values for the MM:SS format can range from -5999s (-99:59) to +5999s (+99:59). Analog inputs: <an_fb1> through <an_fb4000> (continued) Analog Feedback Join Clock Sets the time offset. Decimal values alter the time being displayed by one minute. The analog value is a signed number; if no offset is selected in VT Pro-e, 0d will show the current control system time. A value of 60d will show one hour ahead. A value of -60d will show one hour behind. If a clock offset is selected in VT Pro-e too, the object uses both values to determine the offset. That is, if the offset is set to one hour forward in VT Pro-e and the Analog Feedback Join value is 120d, then the clock object will display three hours ahead. Selects the frame to be displayed on the Animation object. Analog Feedback Join Animation The range of valid values equals the number of frames in the animation, starting at 0d. (Animation can be controlled by Numeric Keypad and Oscillator symbols. Refer also to the Crestron module, Animator. cmc. ) (continued on next page) 30 · Isys i/OTM WiFi Touchpanel: TPMC-10 Operations Guide - DOC. 6284C Crestron TPMC-10 Isys i/OTM WiFi Touchpanel Serial Input & Output Signal Descriptions TOUCHPANEL SIGNAL NAME AND TYPE VT Pro-e JOIN TYPE VT Pro-e OBJECT Border Button Legend Text Gauge Slider DESCRIPTION Indirect Text Join Sends text to the object's text field for display during run time. Serial inputs: <text-o1> through <text-o4000> All serial inputs are permanent. To set the maximum size of the string (recommended), use the optional <Permanent String Size> parameter. Sends a new file path and/or filename to the TPMC-10. If the application is not open, the TPMC-10 will open the file when the Open/Close join for the application goes high. If the embedded application is already open, the new path and file name will not take effect until the application is closed and reopened. Target Join Embedded Application If the string is not valid (i. e. , the target does not exist), the TPMC-10 will send an error code to the control system via the Errors/Warnings analog join for the Project Properties. Logic should then be programmed to handle the error or trigger the "Open File" window. The Target string will persist in the panel's memory until a new string overwrites it, i. e. , the control system sends a new string on the Target join, or the end user selects a new target locally. Operations Guide ­ DOC. [. . . ] Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. [. . . ]