User manual CRESTRON TPS-4500IMW

[. . . ] 9 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Further Inquiries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Future Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Return and Warranty Policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] LF = Load factor of entire run (or chain). The required wire gauge should be chosen such that the resistance value is less than the value calculated in the resistance equation. Refer to the table after this paragraph. Wire Gauge Values RESISTANCE (R) 4 6 10 15 13 WIRE GAUGE 16 18 20 22 24 (Doubled-CAT 5) NOTE: All network wiring must consist of two twisted-pairs. One twisted pair is the +24V conductor and the GND conductor and the other twisted pair is the Y conductor and the Z conductor. NOTE: When daisy chaining network units, always twist the ends of the incoming wire and outgoing wire which share a pin on the network connector. After twisting the ends, tin the twisted connection with solder. Apply solder only to the ends of the twisted wires. Avoid tinning too far up or the tinned end becomes brittle and breaks. After tinning the twisted ends, insert the tinned connection into the network connector and tighten the retaining screw. Repeat the procedure for the other three network conductors. Hardware Hookup Connections to the Back of the TPS-4500IMW The TPS-4500IMW serves as an optional interface between the touchpanel and the Cresnet system. Refer to the illustration after this paragraph for proper connections; apply power last. When making network connections to the CNX Generation control system or Cresnet peripherals, refer to "Network Wiring" on page 4 for details. It is not necessary to make connections to a video source unless the TPS-VID has Operations Guide - DOC. 5913 Wall-Mounted Interface Module: TPS-4500IMW · 5 Wall-Mounted Interface Module Crestron TPS-4500IMW been installed into the touchpanel and a video window object resides on a page within the uploaded VisionToolsTM Pro-e project. Hardware Hookup Connections to the Back of the TPS-4500IMW CONNECT TO VIDEO SOURCE* COMP Y 75 Ohm INPUT + INPUT GROUND C CONNECT TO VIDEO SOURCE* CRESTRON TPS-4500IMW * CONNECTION TO A VIDEO SOURCE IS ONLY NECESSARY IF THE TPS-VID EXPANSION CARD IS INSTALLED INTO THE TOUCHPANEL. POSSIBLE CONNECTION OPTIONS ARE: - NO CONNECTION - UNBALANCED VIDEO (USING COAXIAL CABLE) - BALANCED VIDEO (USING TWISTED PAIR CABLE) DEPENDING ON THE OPTION, THE TWO JUMPERS ON THE NTSC/PAL VIDEO FOUR-PIN CONNECTOR REMAIN ATTACHED (AS SHOWN) OR ARE REMOVED. CONNECT TO CNX GENERATION CONTROL SYSTEM OR CRESNET PERIPHERALS NET 24 Y Z G NOTE: If there is no video source, do not make connections to either NTSC/PAL video connector. However, leave connector and jumpers attached to the NTSC/PAL video four-pin connector on the TPS4500IMW. NOTE: Video balance is determined by external connections. Refer to the two diagrams that follow this note. Unbalanced Using Coaxial Cable 75 Ohm INPUT + INPUT GROUND CONNECT TO COMP Y FOR COMPOSITE VIDEO OR LUMINANCE COMPONENT OF S-VIDEO. INPUT IMPEDANCE EQUALS 75 OHMS. COMP Y C CRESTRON TPS-4500IMW CONNECT TO C FOR CHROMINANCE COMPONENT OF S-VIDEO. 6 · Wall-Mounted Interface Module: TPS-4500IMW Operations Guide - DOC. 5913 Crestron TPS-4500IMW Balanced Using Twisted Pair Cable Wall-Mounted Interface Module 75 Ohm INPUT + INPUT GROUND CONNECT TO COMP Y FOR COMPOSITE VIDEO OR LUMINANCE COMPONENT OF S-VIDEO. JUMPERS REMOVED. [. . . ] Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supercedes all previous warranties. Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. [. . . ]