User manual CRESTRON TPS-RFGWX

[. . . ] Crestron TPS-RFGWX Two-Way RF Transceiver Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2003 Crestron Electronics, Inc. Crestron TPS-RFGWX Two-Way RF Transceiver Contents Two-Way RF Transceiver: TPS-RFGWX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functions and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 4. In the top portion of the "RFGWX Channel ID" window, select the network ID of the gateway that requires the RF channel to be set. In the middle portion of the window, select the desired channel ID for each gateway (up to 16) and all touchpanels (up to 15) associated with that gateway. In the bottom portion of the window, select the desired band for the gateway. The choices correspond with the band names shown in the table on the next page. The table shows the 802. 11b channels within each band that are occupied by the STX-1700CXP. Selection of a band is based on a number of factors, including the need to avoid interference with nearby RF devices, and compliance with local communication laws. In the US, Crestron recommends using Bands 5 (USA comp 1) through 9 (USA comp 5). Bands 1 through 4 (France, Spain, Japan, and Canada) are intended for use in Cresnet systems outside the US. The default setting is Band 0, USA (original), which is not Wi-Fi friendly. Note that at this setting, the gateway can communicate with the touchpanels whether they are Wi-Fi friendly or not, since Band 0 is the default setting for both versions. 10 · Two-Way RF Transceiver: TPS-RFGWX Operations Guide - DOC. Range (MHz) 2400-2474 2448-2474 2448-2474 2471-2497 2452-2477 2400-2425 2409-2435 2419-2445 2430-2455 2440-2465 Two-Way RF Transceiver Band # 0 1 2 3 4 5 6 7 8 9 Occupied 802. 11b Channels Band Name USA (original) France Spain Japan Canada USA (comp 1) USA (comp 2) USA (comp 3) USA (comp 4) USA (comp 5) 1 · 2 · 3 · 4 · 5 · 6 · 7 · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 8 · · · · 9 10 11 12 13 14 ····· ····· ····· ···· ····· · · · · · · · · · · · · In the table, a bullet (·) indicates channels that are used by the STX-1700CXP. The unmarked channels can be used by other devices communicating near the Cresnet system, thus minimizing interference. 5. Select or deselect the Low Power Mode check box as needed. NOTE: The band setting of the TPS-RFGWX and the touchpanel must match in order for them to communicate. From the Viewport menu, select Diagnostics | Report Network Devices and verify that the unit has the desired channel ID. Repeat this procedure for each TPS-RFGWX to be added to the Cresnet system. Hardware Hookup Refer to the hookup diagram below, which shows the TPS-RFGWX connections to the Cresnet system. NOTE: To prevent unit-to-unit RF interference, multiple gateway/transceivers operating at the same frequencies (TPS-RFGWXs and/or Crestron CNRFGWXs) should not be installed within three to five feet of each other. Refer to "Specifications" of each operations guide for the communications frequency of each device. NOTE: Refer to "Network Wiring" on page 8 when making connections to the ports labeled NET. Cresnet System Hookup Connections for TPS-RFGWX TO ANY STS OR CRESNET NETWORK DEVICES FOR NORMAL OPERATION OR FOR PROGRAMMING NET NET NET 24 Y Z G CRESTRON ELECTRONICS INC. 07647 USA TO CONTROL SYSTEM FOR NORMAL OPERATION OR PROGRAMMING Operations Guide - DOC. 5847A Two-Way RF Transceiver: TPS-RFGWX · 11 Two-Way RF Transceiver Crestron TPS-RFGWX Programming Software The TPS-RFGWX provides two-way wireless RF communication between a Crestron control system and a Crestron IsysTM tilt touchpanel equipped with the optional TPS-XTXRF Two-Way RF Transceiver Module or other similarly-equipped Crestron touchpanels, such as the STX-1700CXP. Have a comment about Crestron software?Direct software related suggestions and/or complaints to Crestron via email (software@crestron. com). Do not forward any queries to this address. Instead refer to "Further Inquiries" on page 19 for assistance. Although the device itself is not programmable, you can create a program that includes a TPS-RFGWX using the Crestron programming tool SIMPL Windows. [. . . ] Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. [. . . ]