User manual CRESTRON TPS-VID-1 TPS-VID-2

[. . . ] Crestron TPS-VID-1/TPS-VID-2 Video Card for TPS/Tilt Panel Operations & Installation Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2002 Crestron Electronics, Inc. Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel Contents Video Card for TPS/Tilt Panel: TPS-VID-1/TPS-VID-2 1 Introduction Features and Functions Specifications Physical Description Industry Compliance Installation and Hookup Setup Configuring the Touchpanel VT Pro-e Setup SIMPL Windows Setup Problem Solving Troubleshooting Further Inquiries Future Updates Return and Warranty Policies Merchandise Returns / Repair Service CRESTRON Limited Warranty 1 1 2 4 5 5 12 12 15 16 17 17 18 18 19 19 19 Operations & Installation Guide - DOC. 6059 Contents · i Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel Video Card for TPS/Tilt Panel: TPS-VID-1/TPS-VID-2 Introduction Features and Functions The TPS-VID-1 and TPS-VID-2 video cards are designed for Crestron's IsysTM TPS-4500, TPS-5000, and TPS-6000 tilt touchpanels. [. . . ] If utilizing the TPS-IMC-BV, an external power pack may be connected to the TPS-IMC-BV to supplement Cresnet power or if Cresnet power is not available. CONNECTED TO CRESNET CONNECT TO VIDEO SOURCE(S) FOR TPS-VID-2, USE "COMP/Y" FOR SIGNAL 1 AND "C" FOR SIGNAL 2 24 Y Z G COMP Y C _ S+ COMP Y _ S CRESTRON CAUTION: When running unbalance video, the respective twisted-pair jumper(s) must be installed to avoid damage to the TPS-IMC. Refer to the latest version of the TPS-IMC Operations Guide (Doc. 5856) for hardware hookup details. Operations & Installation Guide - DOC. 6059 Video Card for TPS/Tilt Panel: TPS-VID-1/TPS-VID-2 · 11 AUDIO INPUT TO PANEL TPS-IMC MIC OUT _ S NET/ VIDEO AUDIO Video Card for TPS/Tilt Panel Crestron TPS-VID-1 & TPS-VID-2 NOTE: When using the TPS-VID-2 for receiving two composite video sources, the "Comp/Y" connection will be used for Video Source 1 while the chroma (C) connection will be used for Video Source 2. NOTE: A variety of video wiring combinations can be used. For example, Signal 1 can be connected to the BNC connector while Signal 2 can use the twisted pair connector. Do not apply different video signals to the BNC and twisted pair connector for the same input (i. e. one signal on BNC "Y" input and a different source signal on the twisted pair "Y" input). NOTE: When connecting cables to a TPS-IMC-BV, select the connection to use (BAL or COAX) by sliding the switch to the appropriate setting that is accessible through the opening in the cover of the TPS-IMC-BV. Only one connection type can be used at a time. NOTE: For additional information on video connections over CAT 5, refer to the latest version of the Crestron CAT 5 Wiring Reference Guide (Doc. 6137) which is available from the Downloads | Product Manuals section of the Crestron website (www. crestron. com). Re-connect all cables to the appropriate ports on the rear of the touchpanel. Setup Configuring the Touchpanel NOTE: Refer to the latest revision of the TPS-4500, TPS-5000, or TPS-6000 Operations & Installation Guide (Doc. 5891, 5863, or 5864, respectively) for instructions to access the touchpanel setup screen. The latest version of the operations guide can be obtained from the Downloads | Product Manuals section of the Crestron website (www. crestron. com). From the MAIN MENU, select the SETUP button to access the touchpanel SETUP MENU. 12 · Video Card for TPS/Tilt Panel: TPS-VID-1/TPS-VID-2 Operations & Installation Guide - DOC. 6059 Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel SETUP MENU (TPS-VID-1 shown) NOTE: If the TPS-VID-1 is installed, a single "Video" button will be displayed. If the TPS-VID-2 is installed, buttons labeled "Video 1" and "Video 2" will be displayed instead of the single "Video" button. NOTE: If the video card is not properly installed, the "Video" button(s) will not be displayed. Select the Video button from the SETUP MENU to set preferences for the video source. If a TPS-VID-2 is installed, buttons labeled "Video 1" and "Video 2" will be displayed instead of the single Video button. [. . . ] Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. [. . . ]