User manual CUE INTERFACES

[. . . ] User Manual Interfaces Version 02 CUE, a. s. , Na Dolinách 6, 147 00 Praha 4, Czech Republic phone: +420 241 433 555 fax: +420 241 432 446 www. cuesystem. com e-mail: info@cue. cz User Manual Interfaces UM007_02, 01. 04. 2003 Copyright © CUE, a. s Praha, Czech Republic 1990 - 2003. Specifications are subject to change without prior notice. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This LED diode is blinking if the interface received correctly the data coming from the CUEring. This LED blinks OK by Morse after power on, if auto-diagnostic runs correctly. OUT 1 to 4 (4) LEDs for each output indicate selected input. Indication is as described bellow, lights, means LED lights Microphone input selected Line input A selected Line input B selected Line input C selected Line input D selected POWER Power diode indicates that the interface is powered up. 6. 3. 3. Buttons TEST This button serves for switching over to the testing mode. A detailed description of the testing you can find in the chapter Diagnostic. RESET This button serves for resetting of the interface. During normal operation it is not being used, it solely serves for testing purposes. 9 1 Address Selector Output 1 Indicators Output 2 Indicators Output 3 Indicators Output 4 Indicators Test Button Reset Button Power Supply Indicator means LED no User Manual Interfaces www. cuesystem. com Page 23 of 44 6. 3. 4. Addressing ADDRESS selector It sets address of the interface from 0 to 7. Address identifies interface in the chain. Up to (8) soundCUE interfaces can be installed in one system. The address selector identifies interface by setting it to position 0 to 7. The ADDRESS must be set to different value on each soundCUE in one system. Address of ADDRESS Selector 0 1 2 3 4 5 6 7 OUTPUT 1 and 3 1 3 5 7 9 11 13 15 OUTPUT 2 and 4 2 4 6 8 10 12 14 16 6. 4. Setup by DIP Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DIP-8 switch on the bottom side of the interface is not used and it is prepared for the future use. User Manual Interfaces www. cuesystem. com Page 24 of 44 6. 5. Diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. 5. 1. Level 1 Level 1 diagnostics runs automatically when the soundCUE is powered on or after reset. It checks internal microcontroller circuitry. When the tests are running properly then the DATA O. K. LED starts blinking (by the Morse signal OK). After that the soundCUE is ready for normal operation. 6. 5. 2. Level 2 Pressing the TEST button when the interface is already powered causes the start of the Level 2 testing. It sets · Main volume 0 dB, channel volume 0 dB, bass 0 dB, treble 0 dB · In period of about 2 seconds starts the testing cycle. [. . . ] Trademark Notice CUE and the CUE logo are trademarks of CUE spol. in the United States and in other countries. User Manual Interfaces www. cuesystem. com Page 39 of 44 10. Warranty Conditions Warranty Duration CUE provides warranty for all CUE products for a period of 3 years from the day of purchase. The provided warranty for touch screens is 2 years from the day of purchase. [. . . ]