User manual CUE PEX SOFTWARE

[. . . ] User Manual PEX Software User Manual PEX Software UM031_01, 30. 05. 2007 Copyright © CUE, a. s. , Praha, Czech Republic 1996 - 2007. Specifications are subject to change without prior notice. Table of Contents 1. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Program description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] - Minimum - minimum output value, 0-99 %. - Maximum - maximum output value, 0-99 %. - Intermediate - intermediate output value, 0-99 % for solid state mode. User Manual PEX Software www. cue. cz Page 15 of 25 · Label - Channel legend which can consist of up to 22 characters. 4. 3. 2. Direct control of dimmable channels If the On-line box is checked, any changes made to the parameters Minimum, Intermediate and Maximum are immediately transferred to the output of the module, which makes it possible to control the real brightness of the light source. If the On-line switch is not activated, the output of the module remains unchanged during setting. The current value of the output is shown next to the On-line, being constantly updated. User Manual PEX Software www. cue. cz Page 16 of 25 4. 4. Configuration of the PEA 208 module PEA208 is a two-channel analog output 0 - 10V interface for devices with analog control 0 - 10V (dimmable ballast for fluorescent lamps ­ Osram, Siemens, Helvar, Philips, dimmers, frequency converters . . . ). Fig. PEA 208 parameters description · · · · Interface address 0-15 address of the module. The addresses of both channels of this module are based on this value. Bank 0-9 module group Filter 0-180 msec. Minimum time of pressing the button for the press to be valid. If the time of pressing the button is longer than this value, the press is interpreted as a long press. The following parameters can be set for each channel independently: · Function mode selection for control dimmers by it's buttons - no action - buttons are disabled. - toggle - switch outputs between maximum and minimum values. - solid state - if no button is pressed, the output has the minimum value. If one button is pressed, the output has the value entered in the parameter Intermediate. If both buttons are pressed, the output has the maximum value. - dimmer ­ a short press of the UP/DOWN button changes the output value to maximum/minimum at the speed set in the parameter Short press fade. A long press makes the output dim up/down at the speed set in the parameter Long press fade. A release of the button makes it stop at the currently reached value. - fluorescent ­ a short press of the UP/DOWN button changes the output value to maximum/minimum at the speed set in the parameter Short press fade. A long press makes the output dim up/down at the speed set in the parameter Long press fade. A release of the User Manual PEX Software www. cue. cz Page 17 of 25 - - - - - button makes it stop at the currently reached value. [. . . ] A License is required for each end-user of the Software. A license is required for each installation of the Software. You may make one (1) copy of the Software for archival purposes only. You may use this Software only in connection with CUE hardware. [. . . ]